Go Back  Quiltingboard Forums > Main
Generic Feet for Juki...industrial...high shank??? >

Generic Feet for Juki...industrial...high shank???

Generic Feet for Juki...industrial...high shank???

Old 09-18-2011, 04:15 AM
  #11  
Senior Member
Thread Starter
 
Just-Lee's Avatar
 
Join Date: Jan 2011
Location: Middle of nowhere on a hilltop :)
Posts: 494
Default

Thanks Pinkcastle :) I would like a SID foot too! I believe the TL2010 is the 98 with a few improvements... so I am told lol
Just-Lee is offline  
Old 09-18-2011, 04:17 AM
  #12  
Senior Member
Thread Starter
 
Just-Lee's Avatar
 
Join Date: Jan 2011
Location: Middle of nowhere on a hilltop :)
Posts: 494
Default

Originally Posted by Mitch's mom
Measure your foot. A high shank industrial foot is 1 1/4 inches tall. I found a box of industrial feet at an antique store to fit my Singer 31-15. I then found an attachment box full of domestic machine high shank feet, I can use either or when I'm using the 31-15.
This is exactly what I am talking about! I see antique shop scouring in my near future! Thanks for the tip! :)
Just-Lee is offline  
Old 09-18-2011, 01:26 PM
  #13  
Senior Member
 
pinkcastle's Avatar
 
Join Date: Sep 2011
Location: Washington state
Posts: 474
Default

Originally Posted by Just-Lee
Thanks Pinkcastle :) I would like a SID foot too! I believe the TL2010 is the 98 with a few improvements... so I am told lol
Raichert shows a Stich in the Ditch foot as well:
http://www.raichert.com/azsewingstore/p-JTLF4.htm
pinkcastle is offline  
Old 03-07-2014, 10:44 AM
  #14  
Senior Member
 
Join Date: Nov 2008
Posts: 417
Default Juki 2010 free motion foot

I am surprised Juki has not put out a good free motion open toe foot! I love the feet that came with my 2010Q but I do not love that they are closed toe.
WesternWilson is offline  
Old 03-07-2014, 05:34 PM
  #15  
Super Member
 
GEMRM's Avatar
 
Join Date: Nov 2011
Location: South West Ontario
Posts: 2,235
Default

Originally Posted by Maggiemay View Post
I hve a high shank indusrtial Janome 1600P & all of the feet screw on with a little screw driver- no snap ons or levers to attach the feet. I think that may be the difference between high shank & indusrtial. I need to buy an extra foot to make an open-toed foot too as there is not one made for my machine.
The dealer I had service my 1600 ( I bought it used) sold me an adapter that fit on the 1600 and it made it able to use all the "snap on" Janome feet.
Of course, it was still a straight stitch machine, but at least I could use the stitch in the ditch foot etc.
GEMRM is offline  
Old 03-08-2014, 04:42 PM
  #16  
Member
 
Join Date: Jul 2012
Location: Minnesota
Posts: 70
Default

I am thinking of buying the 2010 but having a hard time justifying it when I have the janome 6500. Thoughts. What do I gain?
Island Queen is offline  
Old 03-23-2016, 12:52 PM
  #17  
REH
Member
 
Join Date: Mar 2016
Posts: 1
Default

I have the Juki 210Q. The website www.thecolorfulworldofsewing has the foot. It is an open toe free motion quilting foot for high speed straight stitch machines like the Juki 2010Q. It is part number HS-P60437 and is $15.99.
REH is offline  
Old 03-23-2016, 10:10 PM
  #18  
Senior Member
 
Join Date: Aug 2010
Location: Albuquerque NM
Posts: 674
Default

i have had good luck finding parts with them, call them:
http://www.ebay.com/sch/i.html?_odkw...+feet&_sacat=0
Phyllis nm is offline  
Old 03-23-2016, 11:03 PM
  #19  
Member
 
Join Date: Jan 2014
Location: suburbs of Dallas, TX
Posts: 64
Default

My Juki 2010 came with two different hopping feet - one with a slightly heavier closed toe ring. I chose to modify the one with the smaller ring, since it would be easier to cut through. Here's what I did to mine, and I absolutely love it now.

Here you can see both feet. The one that I modified is on the right. You can see that I have stuffed a few pieces of corrugated cardboard in there to hold the spring tension, which keeps the foot floating slightly above the fabric. I had to experiment to find the right amount for me (in my case, it's three layers of cardboard and one piece of folded paper). You can also see where I bent the bar that normally rides on the needle bar and makes the foot hop. I bent it up and out of the way so that the foot does not hop.

[ATTACH=CONFIG]545860[/ATTACH]

From this angle you can see the open toe on the modified foot. The tools I used are shown. I used the pliers to bend the bar and keep the foot from hopping. I used the metal file to file open the toe. The toe is made of pretty sturdy metal, so it took some time to cut through. No strength; just patience. It probably took a good thirty minutes to file it open.

[ATTACH=CONFIG]545862[/ATTACH]

I know that it's scary to modify the foot, but hey, the machine came with two of them, and they're (in my opinion) fairly useless for FMQ before modification, and from my experience, the modified foot works fantastically well. Of course, if you do the modifications, I'm not responsible for your results, but I'm super happy with mine now.
Attached Thumbnails 2016-03-24-01.41.39.jpg   2016-03-24-01.42.11.jpg   2016-03-24-01.43.04.jpg   fmq-foot-modification-1.jpg   fmq-foot-modification-2.jpg  

fmq-foot-modification-3.jpg  
colorfulom is offline  
Old 03-24-2016, 05:00 AM
  #20  
Power Poster
 
Join Date: Jun 2011
Location: Southern California
Posts: 19,131
Default

I have an older Bernina and I found that generic feet just don't work as well as the original. I bought my last walking foot on eBay and it was in absolutely new condition even tho it was over a decade since it was made.
ManiacQuilter2 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Notwendy
Main
8
01-29-2019 07:01 AM
sophia
Main
7
11-13-2013 12:25 PM
Jo C
Main
3
10-26-2012 08:19 AM
ShirlinAZ
Main
5
05-23-2012 03:40 PM
auntpiggylpn
Main
21
07-13-2011 06:29 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter