Go Back  Quiltingboard Forums > Main
Help!  Have I ruined my irons?? >

Help! Have I ruined my irons??

Help! Have I ruined my irons??

Old 12-21-2010, 11:14 AM
  #1  
Junior Member
Thread Starter
 
jumpin' judy's Avatar
 
Join Date: Jan 2010
Location: Cedar Hill, TX
Posts: 193
Default

I have been felting wool and decided a really good steaming would be in order-----only I forgot to turn my iron down to "wool". I now have little melted bits of wool on the bottom of two irons. I've tried Spray and Wash, Mr. Clean Magic Eraser, and just plain elbow grease. I am now reading the back of a can of oven cleaner. Anybody got any ideas???
jumpin' judy is offline  
Old 12-21-2010, 11:17 AM
  #2  
Super Member
 
justwannaquilt's Avatar
 
Join Date: Aug 2009
Location: Union, Missouri
Posts: 1,542
Default

You can take a piece of paper bag and put some salt on it, then roll the iron around on the salt. You could always try the iron cleaner goop you can buy at the store. try ironing a damp wash cloth. The key is going to be get the iron hot and THEN clean it while the wool is kinda melted again. once its cooled down and stuck on its harder to get off.
justwannaquilt is offline  
Old 12-21-2010, 11:18 AM
  #3  
Power Poster
 
Join Date: Oct 2009
Location: Idaho
Posts: 11,375
Default

What would happen if you heated the iron and wiped it on an old rag?
Sadiemae is offline  
Old 12-21-2010, 11:19 AM
  #4  
Senior Member
 
Tilladare's Avatar
 
Join Date: Jul 2010
Location: Valparaiso, IN
Posts: 356
Default

I am very curious what your source for the raw wool was, since wool does not melt. perhaps soap residue from the felting process, or a filler in the wool if you used a yarn rather than loose fiber...
Tilladare is offline  
Old 12-21-2010, 11:20 AM
  #5  
Super Member
 
Vanuatu Jill's Avatar
 
Join Date: Jun 2010
Location: Ramona, California
Posts: 2,999
Default

Is the sole plate teflon? My mother taught me a nifty trick to clean the bottom (if not teflon). Take a few sheets of newspaper and lay them stacked on the board and generously sprinkle table salt on it. Heat the iron (No steam) and with a little elboe grease, simply rub the iron over the salt in circular motion, then when clean, take a damp cloth and just wipe it. Worked everytime for me. It doesn't harm the sole plate-I wouldn't use harsh chemicals (oven cleaner).
Vanuatu Jill is offline  
Old 12-21-2010, 11:22 AM
  #6  
Power Poster
 
amma's Avatar
 
Join Date: Jul 2007
Location: Out searching for some sunshine :-)
Posts: 58,856
Default

Sounds like you are using a synthetic and not wool...
I would get the iron really hot and then try to wipe off the worst of it and then try the cleaners when the iron cools off a little :D:D:D
amma is offline  
Old 12-21-2010, 12:11 PM
  #7  
Super Member
 
Deborah12687's Avatar
 
Join Date: Feb 2010
Location: Minnesota
Posts: 1,098
Default

I wonder if those magic erasers would clean it up or use gogone on it. Could also use a brass putty knife to scrape it of as brass doesn't scratch other metals.
Deborah12687 is offline  
Old 12-21-2010, 12:13 PM
  #8  
Super Member
 
Join Date: Feb 2010
Location: Fort Worth, Texas
Posts: 3,291
Default

Whenever there is sticky stuff, like from wonder under, I use a used dryer sheet. Press the dryer sheet with the hot iron and the goo comes off. Don't know if it would work for the felt or not. Worth a try.
KathyAire is offline  
Old 12-21-2010, 12:35 PM
  #9  
Super Member
 
Vanuatu Jill's Avatar
 
Join Date: Jun 2010
Location: Ramona, California
Posts: 2,999
Default

When I get fusible on my iron, a dryer sheet always gets it off-and makes my ironboard smell nice in the process!
Vanuatu Jill is offline  
Old 12-21-2010, 12:42 PM
  #10  
Junior Member
Thread Starter
 
jumpin' judy's Avatar
 
Join Date: Jan 2010
Location: Cedar Hill, TX
Posts: 193
Default

Thanks for all the suggestions. It is 100% wool from recycled clothing that was felted in a hot washer with just a tad of Tide--wonder if that was the culprit? Iron was on "cotton" so it was hot. Some of the wool had an interfacing on it--wonder if that was the culprit?

The oven cleaner immediated cleaned the chrome plate (my Rowenta). The teflon plate was harder to clean for some reason. After reading all kinds of stuff on the internet I tried fingernail polish remover--worked some but required lots of scrubbing. Tried rubbing Lava soap on it--naw, didn't work. Was getting ready to try the salt deal when I went ahead and sprayed the oven cleaner on it. After all, it was a cheap iron. With lots of scrubbing it finally worked.
jumpin' judy is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
kidhauler1948
For Vintage & Antique Machine Enthusiasts
4
08-15-2018 01:05 PM
tezell0801
Main
129
07-28-2012 01:58 PM
cny_sewer39
Main
13
05-21-2011 08:02 PM
tangledthread
Pictures
23
03-19-2011 09:57 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter