Go Back  Quiltingboard Forums > Main
HST using a diagonal cut square >

HST using a diagonal cut square

HST using a diagonal cut square

Old 06-13-2016, 09:58 AM
  #1  
Super Member
Thread Starter
 
Watson's Avatar
 
Join Date: Dec 2015
Location: Ontario, Canada
Posts: 4,347
Default HST using a diagonal cut square

I am starting a pattern that is made up of HST's and the maker of the pattern uses a large square that you layer the two fabrics together, sew a 1/4" seam all the way around then cut diagonally from corner to corner to make 4 HST's. Of course, this is going to make them all bias edges.
What is the best way to handle these HST's without pulling them out of shape? I have starched the fabric, but what else can I do?
Thanks, Watson
Watson is offline  
Old 06-13-2016, 10:01 AM
  #2  
Power Poster
 
Join Date: May 2009
Location: NY
Posts: 10,590
Default

Make them a different way so you don't end up with bias edges. Aside from that starching and handling carefully is all you can do. Personally I would figure out a different way of making them.
feline fanatic is offline  
Old 06-13-2016, 10:16 AM
  #3  
Super Member
 
Join Date: Jul 2012
Location: Vancouver Island, Beautiful BC
Posts: 2,090
Default

Have you already cut the fabric?

If you have, starch is your friend. If not, you can cut 8 HST at a time without bias edges.

http://www.craftsy.com/blog/2014/01/...are-triangles/
Tothill is offline  
Old 06-13-2016, 10:46 AM
  #4  
Senior Member
 
Join Date: Jun 2011
Location: Cedar Falls, IA
Posts: 917
Default

I just finished my first quilt with significant half square triangles (240 of them!), and I had no trouble with cutting squares slightly oversized, cutting down the middle, and carefully sewing the pieces on the cut diagonal. The fabric was well starched, and I handled the cut pieces very carefully. I pressed and then trimmed. I didn't cut more triangles than I could sew in one session to minimize the handling. It seems ridiculous for the pattern designer to give you all those bias edges!

Pam
CanoePam is offline  
Old 06-13-2016, 11:23 AM
  #5  
Super Member
 
Join Date: Nov 2011
Location: Tn
Posts: 8,643
Default

Press them open with care. Use the tip or edge of the iron on th seam only. So not iron the block out of shape
cjsews is offline  
Old 06-13-2016, 11:28 AM
  #6  
Power Poster
 
Join Date: Mar 2009
Posts: 15,639
Default

HSTs are HSTs, regardless of the method used to make them. I recently invested in the Easy Angle ruler and found making HSTs faster, easier, more accurate, no marking, and no bias. I use the Companion Angle for Flying Geese too.

As for the method you described, starch and careful handling should be just fine.
MadQuilter is offline  
Old 06-13-2016, 11:49 AM
  #7  
Super Member
 
gale's Avatar
 
Join Date: Apr 2007
Location: North-Central Indiana
Posts: 4,909
Default

I use another method. This is one reason I didn't keep buying Block magazine. So many of the HST's in there are made this way and I don't want to babysit bias edges.
gale is offline  
Old 06-13-2016, 12:10 PM
  #8  
Super Member
 
Join Date: Aug 2007
Location: Clay Springs AZ
Posts: 3,229
Default

El Burns uses large squares to make 8 HST at a time and not on the bias.
By drawing an x and sewing on both sides of the lines 1/4 in, then cutting the sq in half both ways then on the lines you get 8. 6 in sqs make 2 1/2 in. 8 in sqs make 3 1/2 in and 10 in makes 4 1/2 in.
Rose Marie is offline  
Old 06-13-2016, 03:32 PM
  #9  
Super Member
 
Join Date: Jul 2012
Location: Morris Plains, NJ
Posts: 1,802
Default

Originally Posted by Tothill View Post
Have you already cut the fabric?

If you have, starch is your friend. If not, you can cut 8 HST at a time without bias edges.

http://www.craftsy.com/blog/2014/01/...are-triangles/
I love this Magic 8 method too. If I have enough fabric, I add 1" instead of the 7/8" and then multiple by 2 to get the size of the squares to start with. I will have to trim down but they will be perfect. I gave this tip before but for new people to the QB, I press HSTs to dark side and then put blue painters tape on what will be the low side of my ruler, trim two sides of about 15 (before needing to change the tape), then rotate the HSTs and trim the other two sides.
[ATTACH=CONFIG]552138[/ATTACH]

[ATTACH=CONFIG]552139[/ATTACH]
Attached Thumbnails image.jpeg   image.jpeg  
Maureen NJ is offline  
Old 06-14-2016, 02:43 AM
  #10  
Power Poster
 
Join Date: Jun 2011
Location: Southern California
Posts: 19,131
Default

I just avoid bias edges whenever possible. I have seen too many warped blocks.
ManiacQuilter2 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
nativetexan
Main
15
05-15-2017 06:31 PM
craftybear
Links and Resources
9
03-11-2012 10:06 AM
jbud2
Main
13
01-20-2012 01:58 PM
dmarina
Main
5
07-28-2011 05:24 PM
Ceil
Main
5
04-16-2011 01:09 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter