Go Back  Quiltingboard Forums > Main
Cutting large pieces of fabric >

Cutting large pieces of fabric

Cutting large pieces of fabric

Old 04-21-2017, 04:21 AM
  #1  
Super Member
Thread Starter
 
annesthreads's Avatar
 
Join Date: Mar 2011
Location: South Yorkshire UK
Posts: 1,145
Default Cutting large pieces of fabric

I'm asking a series of quite basic questions at the moment, just to see what methods and ideas you brilliant quilters come up with. I already have several good new tips.

So - now I'm faced with a 4 metre (over 4 yards) length of fabric, which I need to cut to use as a backing. I'm feeling wary because I recently had problems after finding that I hadn't had some fabric lined up absolutely straight before I cut into it. Sometimes it's difficult to find a straight line as a starting point to match up on the cutting board if the selvedges aren't straight and the fabric hasn't been cut straight when taken off the bolt. And, of course, it's just difficult to work with a long piece of fabric - folding, lining up, cutting.

Any hints or tips?
annesthreads is offline  
Old 04-21-2017, 06:11 AM
  #2  
Power Poster
 
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 41,444
Default

​The only time I rip fabric is when I need to do long borders. I will rip off the width I need down the whole length but with an inch to spare. After ripping I fold it up and trim the ripped edge off. If I need to cut lengths, I always use my large 15 inch square lined up on the fold to prevent V mistakes in the length.
Tartan is offline  
Old 04-21-2017, 06:12 AM
  #3  
Super Member
 
luvstoquilt301's Avatar
 
Join Date: Dec 2009
Location: Phoenix AZ
Posts: 1,018
Default

I just tear larger pieces. BUT you must be sure you have some extra as you will sometimes lose yardage when doing this.
I don't think I would be successful cutting it perfectly.
luvstoquilt301 is offline  
Old 04-21-2017, 06:27 AM
  #4  
Power Poster
 
Join Date: May 2008
Location: MN
Posts: 24,370
Default

I think it is important to follow grainlines - because I think a quilt, blanket, sheet, towel, handkerchief - is easier to fold neatly when it is cut on-grain.

First, I wash and dry the fabric to see what it wants to do "on its own."

Then I look carefully to see what I have for grain lines on the ends.

If I have "extra" - I will tear it to get an on-grain edge. Tearing does cause trauma to the ends. Sometimes the damage can extend several inches into the fabric.

If I have to be careful with what I have available - I will pull a thread - which is tedious - but it does work.

I do remove the selvages from backing material. Most selvages are more tightly woven than the rest of the fabric - and some of them shrink a lot more than the rest of the fabric. So they get cut off.

If only a scant amount of fabric is available - then I suppose you will have to "make do" with what you have.
bearisgray is offline  
Old 04-21-2017, 06:58 AM
  #5  
Super Member
 
Join Date: Jul 2010
Posts: 1,029
Default

I too tear usually but always make sure I have a bit extra and usually the torn part is the extra inches on either side of the backing since I like my backings at least 3 inches larger on all sides.
luvspaper is offline  
Old 04-21-2017, 07:20 AM
  #6  
Power Poster
 
sewbizgirl's Avatar
 
Join Date: Oct 2010
Location: Mississippi
Posts: 25,893
Default

I always rip large pieces... for backs or for borders. It's fast and it's accurate.
sewbizgirl is offline  
Old 04-21-2017, 07:48 AM
  #7  
Power Poster
 
QuiltnNan's Avatar
 
Join Date: Mar 2011
Location: western NY formerly MN, FL, NC, SC
Posts: 51,433
Default

I've become a fan of ripping/tearing lately, too.
QuiltnNan is offline  
Old 04-21-2017, 08:27 AM
  #8  
Super Member
 
Join Date: Feb 2014
Location: Wis
Posts: 5,928
Default

I also rip to get it straight especially for a large piece of backing
Doggramma is offline  
Old 04-21-2017, 08:37 AM
  #9  
Banned
 
Join Date: Aug 2014
Location: Victorian Sweatshop Forum
Posts: 4,096
Default

I don't like to rip fabric, call me weird. For piecing a backing, I just fold it in half and cut it with scissors on the fold line. Since it will be sewn on the selvedge edge, it doesn't matter if the cut is perfectly straight.

Cari
Cari-in-Oly is offline  
Old 04-21-2017, 09:21 AM
  #10  
Super Member
 
Pennyhal's Avatar
 
Join Date: Oct 2010
Location: California
Posts: 1,732
Default

If the fabric is printed, it may be printed off grain. So tearing wouldn't work with those unless it does not matter if the print is on grain too. I learned this the hard way. sigh.
Pennyhal is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
I Am Trying
Main
39
02-08-2010 11:30 AM
kyssyfur
Main
15
08-13-2008 09:32 AM
NewsletterBot
Main
4
10-04-2007 10:44 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter