squaring up a quilt top?
 

is there a easy way to check to see if your top is square before you put the boarder on... I have a queen top done and it has given me more head aches and now I think it may be off and not square...the quilt is the one on the MSQC tutorial video it is called periwinkle, I thought that it would be a easy quilt to make as you use the paper from the company and the template.

I didn't use the wacky web template that they show in the video as I heard that the points didn't come out right, so I used the one out of the magazine that had the pattern in it, my hubby cut me one out of plastic so it works great but the pieces didn't go together as I thought they would ...like I said I had so much trouble sewing the pieces together and was almost ready to give up...

it was like the quilt didn't lay flat even after I pressed it using spray starch..I don't know if it is because the pieces are cut on the bias or what ..also because I used white for the back ground if you didn't press the seams the right way they didn't line up and you could see that ..hoping that after it is quilted that part of the booboo won't show to much..any help on this problem or if someone could tell me what I did wrong to make the quilt top not lay flat would be great to know for the next time if there will be a next time LOL Thanks so much..

Looks to me as if there are a lot of bias edges on those pieces. What would have helped is heavily starching the fabric *before* cutting. (I use a 1:1 solution of Sta-Flo laundry starch and water, which is much stronger than just spray starching.)

If you use a white batting, the white seams will tend not to show through.

Because of the edges you have on this quilt, you would be best off blocking the top. What I would probably do is lay a large flat sheet on carpeting, spread the quilt top on it, and then start measuring and pinning. I would pin the middles first, measure those, and then strive to get the ends pinned down to the same measurements. (You might need to secure the flat sheet to the carpeting with pins or painter's tape so it doesn't move around on you.) Once you are satisfied that it is as straight as you can get it, try misting the top with hot water (if you have a steam iron, you could hold the iron above the fabric and mist it with steam). Put a fan on it to speed drying. Finally, I would mist the top with several layers of spray starch, drying in-between layers, to add stability to the blocking.

I would plan on doing fairly heavy all-over quilting with a fine thread (such as Bottom Line or Aurifil 50wt 2-ply). Lots of the distortion will become hidden in heavy quilting.

Take a bunch of measurements on the width and length of your quilt and see how much if any you are out. It could be more of a problem of cupping in the individual blocks rather than the quilt being out of square and if that is what is happening you might need to "tighten" a few seams to reduce the bulk in the offending blocks. Some cupping can be disguised in the quilting process but this can be quite an undertaking. Hope you find a solution, good luck

Wash and dry after quilting, hides a multitude of boo boos. I never have to square my quilts. I measure through the center for the borders.

Prism99 is correct. you need to block the quilt, and starch it as much as possible. The fabric needs to be as stable as possible to keep the edges as stable as possible. If it comes out feeling like cardboard, great! that's perfect. Starch will wash, right now you need stiff as a board. Once you have starched and blocked it. Measure the depth of each white along the outer border. Measure from the point to the center of the outer edge of each block. When you have found the smallest one along each side, use that measurement to trim your sides.Check the full size of an existing block in the middle, and cut it in half. that measurement is what the half blocks should be. But done be alarmed if you have to make your half blocks a little smaller to square it up. that measurement is just a guide so to help you get a feel for how much you are cutting off your quilt sides. Also, don't "Iron" your quilt. that will push it out of shape. Always press it. Spray starch an area and press until dry by lifting up and down, never slide side to side. Don't panic that quilt looks beautiful, and, unless you have balloons , a good long arm quilter will be able to disguise any bubbles. I am a long arm quilter, and I just had a wedding ring quilt that looks like bazooka bubble gum. And it turned out gorgeous.

Thanks ladies I will try and starch it and see what happens, I just feel so bad that it came out like this... I don't think I will be doing another quilt with so much bias to deal with...first time for me working with this and hope it will be the last... I do like the looks of the quilt but sad how it came out..Thanks again

It's still a very pretty quilt, so do the best you can, try not to worry about it too much, and enjoy it!

Your quilt is beautiful!!! Don't give up! If we don't try things that are a bit of a challenge we will never learn new wonderful things. You've been given some helpful hints here, do the ones that you feel will help the most, then finish it, you will be surprised how wonderful it will be once quilted.

I think it is a beautiful quilt and agree that some may be cupping. I think with squaring and quilting a multitude of things will disappear. Really very pretty.