Go Back  Quiltingboard Forums > Main
Scant Quarter Inch >

Scant Quarter Inch

Scant Quarter Inch

Old 03-16-2011, 11:01 AM
  #1  
Senior Member
Thread Starter
 
GloriaC's Avatar
 
Join Date: Feb 2011
Location: Lancaster, SC
Posts: 349
Default

Can someone explain to me how you judge a scant quarter inch. I'm fairly new to quilting and this phrase kinds scares me. How do you judge what scant is?
GloriaC is offline  
Old 03-16-2011, 11:03 AM
  #2  
Senior Member
 
LaurieE's Avatar
 
Join Date: Mar 2009
Location: Alachua, Florida
Posts: 678
Default

The best way that I can explain it is - sew just inside the quarter inch line. A quarter inch is 4/16 (on the ruler). Sew between 3/16 and 4/16 as marked on the ruler.
LaurieE is offline  
Old 03-16-2011, 11:04 AM
  #3  
Power Poster
 
Join Date: Oct 2009
Location: Idaho
Posts: 11,375
Default

I have heard that it is one or two threads shy of a quarter, but I personally think it is hard to judge.
Sadiemae is offline  
Old 03-16-2011, 11:06 AM
  #4  
Power Poster
 
erstan947's Avatar
 
Join Date: Feb 2010
Location: Louisiana
Posts: 12,166
Default

I judge it by 2 or 3 threads from ¼ in line. I place a piece of painters tape about 1½" long close to my needle to help me be consistent.
erstan947 is offline  
Old 03-16-2011, 11:24 AM
  #5  
Power Poster
 
Join Date: Dec 2008
Location: Western Wisconsin
Posts: 12,930
Default

It's different for every sewer and every machine (and depends also on fabric and thread).

Basically what you have to do is test until you get it right. Cut 2.5" strips of fabric (maybe 6" long). Sew 3 of the pieces together with what you think is a scant 1/4" seam. Iron, then measure. With perfect 1/4" seams, the piece should measure 6.5". If it's less than that, then you need to reduce your seam width and try again.

Here's what I do to achieve perfection (ahem.....). I take one of my cutting rulers and place it under the presser foot of my machine. I lower the needle until it touches the 1/4" line, but then move the ruler slightly so the needle touches just a little to the side of the ruler's 1/4" line. I lower the presser foot to hold the ruler in place. I also check to make sure that the ruler is straight from front to back. Then I take a strip of moleskin (that I have already rotary cut), peel off the paper backing, then stick it to the base of machine right next to the ruler's edge. (Moleskin is sold in the foot section of a pharmacy. It is a thick adhesive-backed material used to protect feet blisters.) The moleskin provides me with a physical guide for feeding my strips into the machine so I don't have to stare at a mark.

At this point, you should test with the 2.5" strips to make sure the end result is accurate.

Instead of a ruler, you can use graph paper that has 4 squares to the inch.

The reason for the "scant" seam allowance is so the end result will be the correct measurement. Seams require some turn-of-the-cloth that uses up a little bit of the fabric. If the seam is an exact 1/4", then the end measurements after pressing and many seams will be short. Also if you are using thick fabric and/or thick thread, the turn-of-the-cloth will take up even more of the fabric. Better to take a little off each seam than to end up with a block that is 1/4" short from all the seams in it.
Prism99 is offline  
Old 03-16-2011, 11:54 AM
  #6  
Senior Member
 
Join Date: Oct 2010
Posts: 647
Default

I personally think this scant business is just to make you crazy. I sew a quarter inch. One of my latest quilts had 159 seams along the length. When I measured for the border the overall length was off less than one sixteenth of an inch. This is were don't sweat the small stuff comes in.
Kat Sews is offline  
Old 03-16-2011, 12:57 PM
  #7  
Power Poster
 
Join Date: Dec 2008
Location: Western Wisconsin
Posts: 12,930
Default

Kat, you must live right!
Prism99 is offline  
Old 03-16-2011, 01:19 PM
  #8  
Super Member
 
feffertim's Avatar
 
Join Date: Jan 2011
Location: Desert Hot Springs Ca
Posts: 2,633
Default

I use a 1/4 inch foot and move my needle over one or two spots.
feffertim is offline  
Old 03-16-2011, 01:24 PM
  #9  
Senior Member
 
Rachel's Avatar
 
Join Date: Sep 2009
Location: Iowa
Posts: 879
Default

Originally Posted by Kat Sews
I personally think this scant business is just to make you crazy. I sew a quarter inch. One of my latest quilts had 159 seams along the length. When I measured for the border the overall length was off less than one sixteenth of an inch. This is were don't sweat the small stuff comes in.
Well Said!!! I think as long as you're consistent it really doesn't matter. Or at least it hasn't in any of the projects I've done so far. :)
Rachel is offline  
Old 03-16-2011, 01:31 PM
  #10  
Senior Member
 
Join Date: Jan 2011
Location: Glen Burnie, MD
Posts: 927
Default

Originally Posted by Rachel
Originally Posted by Kat Sews
I personally think this scant business is just to make you crazy. I sew a quarter inch. One of my latest quilts had 159 seams along the length. When I measured for the border the overall length was off less than one sixteenth of an inch. This is were don't sweat the small stuff comes in.
Well Said!!! I think as long as you're consistent it really doesn't matter. Or at least it hasn't in any of the projects I've done so far. :)
I agree with Kat and Rachel. I don't think it matters so much as long as your cosistent with the 1/4 inch it self.
susanwilley is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
DOTTYMO
Main
28
06-25-2015 06:28 PM
GagaSmith
Main
45
07-13-2011 07:30 AM
ShirlR
Main
18
09-07-2010 07:52 AM
2wheelwoman
Introduce Yourself
20
10-30-2008 02:09 PM
ProquiltLongarmARTQUILTER
Main
25
02-20-2008 07:09 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter