Go Back  Quiltingboard Forums > Main
Size of blocks? >

Size of blocks?

Size of blocks?

Old 07-11-2009, 03:08 PM
  #1  
Senior Member
Thread Starter
 
MoMoSews's Avatar
 
Join Date: Jul 2009
Location: Illinois
Posts: 768
Default

OK ladies, I'm fairly new to the quilting world and I am really stumped when trying to figure out what size blocks to cut to frame the center of my quilt top when not using a purchased pattern. Say my center is 36x36 and I want to use 2, 3 or 4inch half square triangles. How do you figure that out. Is there a chart I can download? Cause figuring all the seam allowance makes my head spin. :cry:
MoMoSews is offline  
Old 07-11-2009, 04:10 PM
  #2  
Super Member
 
mpspeedy's Avatar
 
Join Date: Mar 2008
Location: rural Maryland
Posts: 1,564
Default

Ok some may disagree with me.
If it were me I would cut squares of two different colors or prints the same size. Enough to go around your center piece. Make sure you make the same mount of both. Now lay them right sides together, draw a line diagonally down the middle and sew 1/4 inch on either side of that line. Now cut them apart on the middle line and press open. You should have two triangles sewn together into a square. The bias is on the seam line so they should not stretch a lot. use the squares to make your border. It doesn't really matter what size they are as long as they are all the same they should come out a consistant size. I think it is traditional to pick the size block you want finished and add 7/8 of an inch to that measurement when cutting the blocks. The only problem I have with that is that precise a measurement always gets me in trouble. I tend to stick with whole numbers and trim down if necessary.
I also find that adding an inch or even two border between the center and the border of triangles is more interesting, helps the quilt grow and is easier on the eye. A little wider plain border after the triangle border usually looks good .
mpspeedy is offline  
Old 07-11-2009, 04:35 PM
  #3  
Senior Member
Thread Starter
 
MoMoSews's Avatar
 
Join Date: Jul 2009
Location: Illinois
Posts: 768
Default

OK. I was wondering how to figure out how many triangle blocks (whatever size I chose) to line up exactly with the edges of my quilt center.
I'm not very good at explaining this. Example ..If I needed to make a border of 3" blocks to equal 36". what size blocks do I cut, figuring in the seam allowances?
MoMoSews is offline  
Old 07-11-2009, 04:47 PM
  #4  
Banned
 
Join Date: Apr 2009
Location: Sleepy Hollow, NY
Posts: 4,727
Default

if you're quilt measure 36 inches and you want to figure out what sizes you could use - i would go with any number that divides into 36 equally.

36/2 inches = 18 blocks
36/3 = 12
36/4 = 9
36/5 = no good, its not a whole number
36/6 = 6 blocks
36/8 = no good, its not a whole number

so, you get the idea. now you should decide what size block will look good with the style of the quilt. that really just comes down to what you like and the look your going for.

the cuts you have to make to achieve the correct finished size is 7/8 larger for triangles and 1/2 larger for straight cuts - this accounts for the seam allowances.

kluedesigns is offline  
Old 07-11-2009, 05:00 PM
  #5  
Super Member
 
Moonpi's Avatar
 
Join Date: Mar 2007
Location: Central FL
Posts: 4,829
Default

Just adding that you also need to add 4 corner blocks in your calculations , in additon to the sides, top and bottom.

It's a good example of why odd sizes don't always work out right. Sometimes it is easier to add a border in order to bring the hst layer into easier calculations.
Moonpi is offline  
Old 07-11-2009, 05:01 PM
  #6  
Senior Member
Thread Starter
 
MoMoSews's Avatar
 
Join Date: Jul 2009
Location: Illinois
Posts: 768
Default

Thank you so much! That is what I needed to know. I figured it had to be something simpler than what was going on in my brain! I can see now that this forum is going to be a wealth of information. You're all the best.
MoMoSews is offline  
Old 07-11-2009, 05:43 PM
  #7  
Banned
 
Join Date: Apr 2009
Location: Sleepy Hollow, NY
Posts: 4,727
Default

Originally Posted by Moonpi
Just adding that you also need to add 4 corner blocks in your calculations , in additon to the sides, top and bottom.

It's a good example of why odd sizes don't always work out right. Sometimes it is easier to add a border in order to bring the hst layer into easier calculations.
thank you moonpi, i would have felt terrible when she posted that she doesn't have any corners :shock:
kluedesigns is offline  
Old 07-11-2009, 07:33 PM
  #8  
Power Poster
 
Join Date: May 2008
Location: MN
Posts: 24,370
Default

Suggestion:

maybe make two or threetest HST squares and then join them together to make sure they are coming out to the expected size before you cut out a lot of them.

I find that cutting the squares plus one inch and trimming the excess works out better for me. The plus 7/8 ones end up skimpy for me.

And you will find MANY suggestions for how to make HSTs here.
bearisgray is offline  
Old 07-11-2009, 07:34 PM
  #9  
Power Poster
 
Join Date: May 2008
Location: MN
Posts: 24,370
Default

I do a lot of trials because I kind of make a lot of errors.

So - that's why I have all suggestions for making samples -
bearisgray is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Moonpi
Pictures
16
09-22-2012 01:42 PM
huntannette
Links and Resources
11
04-19-2011 02:05 PM
cindle
Main
19
11-18-2010 07:51 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter