Starching cut pieces?
#1
Starching cut pieces?
I am working on my first quilt and have all the pieces cut and laid out on my design board. I now find that I should have starched my fabric. Is it too late? Can I spray starch? When and who is the best way to starch so I don't do this again!!
#3
Super Member
Join Date: Jan 2012
Location: The Colony, TX
Posts: 3,364
In the future if you are going to starch it is best if you do so before you cut. There is no rule that says you have to starch - I do think my cuts come out better if I do, but that is just my personal opinion
#4
Super Member
Join Date: Dec 2010
Location: Norfolk, VA
Posts: 5,397
go ahead and starch. spray them and let it set for a few seconds until the white foam disappears so that you won't get the white residue and then becareful and not move your iron too much so you don't stretch you fabric. You don't always have to starch but if I'm doing angles then it's a good idea for sure. If I'm doing a block and need it to lie flat I'll starch it.
#5
Power Poster
Join Date: Dec 2008
Location: Western Wisconsin
Posts: 12,930
I would probably wait to spray starch until after you have completed a block. At that point you can use spray starch to "block" the block to correct size.
Starching before cutting, just as with washing before cutting, is a personal preference. I don't starch fabrics before cutting, but then I also don't prewash. Starching, for me, is not necessary for fabric right off the bolt because that fabric already contains some sizing from the manufacturer. If I need to wash a fabric, however, washing removes the manufacturer's sizing and can leave the fabric limp. That kind of fabric I will starch before cutting, to restore some stability and stiffness to the fabric.
Did you wash this fabric before cutting out the pieces? In that case, you do have the option of spray starching before piecing, as you can be pretty sure the cut pieces won't shrink or bleed. If the fabric was not pre-washed, you run the risk of the pieces shrinking or distorting if you spray starch. Besides, unwashed fabric usually has enough sizing in it so that starch is not needed.
In a situation where I need extreme exactness in piecing, I would heavily starch unwashed fabric before cutting to ensure extremely precise cutting and piecing. A few quilters do this routinely. I just skip any step that I think is not absolutely necessary, as it takes me long enough to complete a quilt already!
Starching before cutting, just as with washing before cutting, is a personal preference. I don't starch fabrics before cutting, but then I also don't prewash. Starching, for me, is not necessary for fabric right off the bolt because that fabric already contains some sizing from the manufacturer. If I need to wash a fabric, however, washing removes the manufacturer's sizing and can leave the fabric limp. That kind of fabric I will starch before cutting, to restore some stability and stiffness to the fabric.
Did you wash this fabric before cutting out the pieces? In that case, you do have the option of spray starching before piecing, as you can be pretty sure the cut pieces won't shrink or bleed. If the fabric was not pre-washed, you run the risk of the pieces shrinking or distorting if you spray starch. Besides, unwashed fabric usually has enough sizing in it so that starch is not needed.
In a situation where I need extreme exactness in piecing, I would heavily starch unwashed fabric before cutting to ensure extremely precise cutting and piecing. A few quilters do this routinely. I just skip any step that I think is not absolutely necessary, as it takes me long enough to complete a quilt already!
#7
Super Member
Join Date: Feb 2010
Location: Maryland
Posts: 3,586
If I forget to starch before I cut, I generally will spray starch the pieces and let them dry all the way before I press. I can never get it right if I press while the fabric is damp/wet--it either shrivels up or stretches out--operator error?probably--but letting it dry cuts down on my catastrophes.
#8
Junior Member
Join Date: Nov 2010
Location: Elkhorn, WI
Posts: 127
I don't starch very often. When I do it is cause the fabric is kinda wimpy and I am sewing some pointy triangles. If I have lots to do, I'd lay down some scrap pressing sheet on the ironing board first, just so it doesn't get all scuzzy. then I'd lay lot's of pieces down close together cause that spray goes everywhere. then like the others suggested spray and let set till foam goes away and press up and down to dry. Move when cool.
I don't usually spray yardage, but I will decide to spray after I cut strips - occasionally.
I don't usually spray yardage, but I will decide to spray after I cut strips - occasionally.
#9
Thread
Thread Starter
Forum
Replies
Last Post