Go Back  Quiltingboard Forums > Main
Will any of these 3 work? >

Will any of these 3 work?

Will any of these 3 work?

Old 12-09-2012, 04:24 PM
  #11  
Super Member
 
Join Date: Apr 2010
Location: Illinois
Posts: 9,312
Default

Eleanor Burns method uses a fusible interfacing on one side. You sandwich the fabric and fusible together. Right side of fabric to fusible side of interfacing. Sew around the shape , trim to a scant 1/4 inch around the stitched line. Make a small clip in the interfacing in the center, enough to turn the applique to its right side. The fusible interfacing will now have the the fusible in the same direction as the wrond side of the fabric. Use a bodkin or other point turner( through the clipped portion) to shape the applique into its final shape. Then fuse the applique into its final postion on the block. This method turns the raw edges under , using the interfacing as a "lining" .. the fusible side will hold it in postion while you stitch around the applique.
I prefer this method as there is no raw edge, and if done properly can closely resemble needle turn... or as close as I have seen without actually doing needle turn. Use a fine thread and a small "bite" blanket stitch to do the actual stitching of the applique on the block.
One note .... its very tempting to try to iron the applique before postioning on the quilt ( finger pressing is very useful at this point) ... make sure if you do this you have a teflon sheet or other non- stick pressing surface.
Some trim out the block fabric and interfacing once sewn, to the seam allownce that was turned under...This really gives even more of a needle turn effect.
Lori S is offline  
Old 12-10-2012, 05:36 AM
  #12  
Super Member
Thread Starter
 
Join Date: Aug 2010
Location: Quilt Dreamland
Posts: 1,601
Default

THANK YOU so much everyone!
LavenderBlue is offline  
Old 12-11-2012, 04:53 AM
  #13  
Super Member
 
jitkaau's Avatar
 
Join Date: Aug 2010
Location: Australia
Posts: 4,116
Default

None of those are likely to work with her method. You need to get light weight interfacing that is fusible on one side only.
jitkaau is offline  
Old 12-11-2012, 06:34 AM
  #14  
Senior Member
 
MarthaT's Avatar
 
Join Date: Apr 2010
Location: South Alabama
Posts: 711
Default

Just remember, if hand quilting, the interfacing can add enough bulk to make it challenging to make tiny stitches. The lighter interfacing the better if you plan to hand quilt through the appliqued pieces.
MarthaT is offline  
Old 12-11-2012, 07:11 AM
  #15  
Super Member
 
Join Date: Jun 2011
Location: Illinois
Posts: 9,018
Default

as a side note regarding the fusible interfacing.....also make sure it is non-woven......so remember, non-woven fusible lightweight interfacing..it is a mouthful, but the non-woven part makes a bit of difference....no stretch when you turn it right side out again........holds the shape.......and it is very inexpensive... a good thing to use those coupons from JoAnn's for....
Geri B is offline  
Old 12-11-2012, 07:28 AM
  #16  
Senior Member
 
Join Date: Mar 2011
Posts: 471
Default

I use this method and use Wonder Under.
topstitch is offline  
Old 12-11-2012, 07:43 AM
  #17  
Super Member
 
Join Date: Mar 2012
Location: Southeast Georgia
Posts: 2,526
Default

I wouldn't use any of those. You need fusible interfacing like the kind that is used in sewing garments. It works like a charm. Just make sure when you go to cut the hole for turning, that you only cut the interfacing and not the fabric. This method makes beautiful applique pieces.
MimiBug123 is offline  
Old 12-11-2012, 09:45 AM
  #18  
Super Member
 
nstitches4u's Avatar
 
Join Date: Apr 2011
Location: Independence, MO
Posts: 3,560
Default

Steam-A-Seam 2 has adhesive on both sides. It is made for fusible applique, but not the stitch and turn variety. Be sure your Heat n Bond is the SEWABLE variety. Some of their products for crafts are not sewing machine friendly. They gum up your needle and cause stitching problems. (Ask me how I know. lol) The ones made to be sewn are fine.

Last edited by nstitches4u; 12-11-2012 at 09:47 AM.
nstitches4u is offline  
Old 12-11-2012, 10:53 AM
  #19  
Senior Member
 
Join Date: Feb 2012
Posts: 432
Default

this sounds like a place where the Easy Knit fusible would work great. light weight, flexible for turning and won't add bulk to your quilt.
riutzelj is offline  
Old 12-11-2012, 11:02 AM
  #20  
Super Member
Thread Starter
 
Join Date: Aug 2010
Location: Quilt Dreamland
Posts: 1,601
Default

I appreciate all of these replies! Will be 40 miles away at my nearest Joann's on Thursday. :-)
LavenderBlue is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
dd
Main
18
10-10-2013 06:39 AM
barnbum
Pictures
17
09-28-2012 12:00 PM
Sweetness
Main
9
12-06-2010 11:42 AM
chamby
Main
128
04-23-2010 05:27 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter