Go Back  Quiltingboard Forums > Tutorials
Glue Basting With Elmer's School Glue >

Glue Basting With Elmer's School Glue

Glue Basting With Elmer's School Glue

Old 11-24-2009, 05:55 PM
  #1  
Power Poster
Thread Starter
 
amma's Avatar
 
Join Date: Jul 2007
Location: Out searching for some sunshine :-)
Posts: 58,856
Default

I have been asked how I use Elmer's Glue for basting blocks and binding. So while putting binding on today I snapped a few pictures to demonstrate how I do it. The glue washes out easily, it does not gum up my needle, and I have tried hand sewing through it and had not trouble with that either.
Keep the glue in the seam, if it leaks out it will wash out of the fabric, no problem....but I do not care to clean my iron's sole plate any more often than necessary :wink:
It is very helpful to have this small applicator tip...you only need a very fine line or very small drops. Coming out of the regular bottle's tip is too much and hard to control. I got this bottle for 49 cents at a thrift store. You can refill these bottles with regular Elmer's White School Glue. Another alternative is to squirt some glue out onto a piece of aluminum foil and use the tip of a toothpick...I tried this in a pinch, but it does take longer doing it this way. If it is just to align/match seams, it works fine.
To align/match seams, I only DRY IRON for a quick 3 count...for bindings sometimes to 5...check and see how long it takes to set the glue.
I used more than necessary to match the seams in these pictures so that the drops showed up...3 small drops...if you shift it, gently peel them apart and reglue and iron.
Practice on some orphan blocks like in the picture...mine are pinned down just to free up my hands to take the pictures. I match the seams, glue and pinch the area with my fingers and then hit it with the iron.

HINT
Let a drop of glue dry on the tip of the tube before putting the cap on...it will seal it better. If glue dries in that little tube, it is really hard to get unclogged!!!
[ATTACH=CONFIG]55366[/ATTACH]
Attached Thumbnails attachment-2638.jpe   attachment-2639.jpe   attachment-55366.jpe  
amma is offline  
Old 11-24-2009, 05:58 PM
  #2  
Power Poster
Thread Starter
 
amma's Avatar
 
Join Date: Jul 2007
Location: Out searching for some sunshine :-)
Posts: 58,856
Default

Binding sewn onto the back and ready to be glued down.

I place the glue dots where they will not come out past the binding after being ironed.

Iron to the count of 3-5 seconds....on a setting to match your fabric and NO STEAM.

Sometime I do pin the quilt to my ironing board so that it cannot slip off while glue basting.
[ATTACH=CONFIG]55231[/ATTACH]
Attached Thumbnails attachment-2785.jpe   attachment-2801.jpe   attachment-55231.jpe  
amma is offline  
Old 11-24-2009, 06:03 PM
  #3  
Power Poster
Thread Starter
 
amma's Avatar
 
Join Date: Jul 2007
Location: Out searching for some sunshine :-)
Posts: 58,856
Default

You can see even my mitred corner is started here, too. Everything is basted down.
Now I add just a drop more the the corner of the mitre to hold it in place when folded down and iron.

More dots of glue and iron the binding down.

The mitred corner looks pretty good, huh? 8) Even better in person without the shadows picked up by the camera :wink:

Continue all the way around your quilt and then sit down and sew it by hand or machine and now worries about getting poked, sewing over pins, or the pins hanging up on the quilt.
Attached Thumbnails attachment-2402.jpe   attachment-2415.jpe   attachment-2416.jpe  
amma is offline  
Old 11-24-2009, 06:25 PM
  #4  
Super Member
 
Join Date: Jun 2009
Location: Central Illinois
Posts: 2,329
Default

Thanks so much for sharing. Good photos and directions!
Teacup is offline  
Old 11-24-2009, 06:36 PM
  #5  
Power Poster
 
Join Date: Jul 2008
Location: Northern Indiana
Posts: 20,306
Default

THANKS :lol:
sharon b is offline  
Old 11-24-2009, 06:48 PM
  #6  
Senior Member
 
justme's Avatar
 
Join Date: Mar 2008
Location: MICHIGAN
Posts: 843
Default

Thank you Amma :-)
justme is offline  
Old 11-25-2009, 01:09 AM
  #7  
Administrator
 
patricej's Avatar
 
Join Date: Nov 2006
Location: Southeast Georgia, USA
Posts: 9,088
Default

ok. YOU are my hero!

i glue baste, too, when doing narrow bindings. but no matter how hard i try i simply cannot get the sharp, crisp, perfectly angled mitres you make.

i bow in awe and wonder. :shock: :P :P :P
patricej is offline  
Old 11-25-2009, 07:20 AM
  #8  
Power Poster
 
Ninnie's Avatar
 
Join Date: Mar 2009
Location: Athens Ga
Posts: 11,420
Default

What a great tute!! Thanks!
And I am so envious of your mitered corners, mine never look that good!!!
I will try harder :roll: :roll:
I like this, especially for the bigger quilts that i do, no pins, I am always sticking myself :shock: :lol: :lol:
Ninnie is offline  
Old 11-25-2009, 07:57 AM
  #9  
Power Poster
 
Join Date: Jan 2008
Location: Florida
Posts: 17,636
Default

Hurray! was basting last night and my hand slipped...yup, jabbed pin right up under left thumbnail :shock: :evil: :!:
Now I got me some pictures, I am gonna become a glue basting fool :mrgreen:
No more jabs for me...maybe :oops:
Hugs for sharing Amma. Your corner looks awesome! :wink:
Mousie is offline  
Old 11-25-2009, 08:52 AM
  #10  
Junior Member
 
mysacrifice's Avatar
 
Join Date: Sep 2009
Location: Central Arkansas - Conway Area
Posts: 219
Default

Amma, can I ask you a question? This is probably a stupid one, but do you stitch down the front first then glue down the back followed with additional stitching? If so, does the stitch show on the front? I'm confused. So sorry to ask so many questions. Thank you in advance.
mysacrifice is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
carslo
Tutorials
113
02-23-2014 04:01 PM
frannella
Main
27
02-20-2012 07:55 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter