Go Back  Quiltingboard Forums > Tutorials
tut for quilting frame >

tut for quilting frame

tut for quilting frame

Old 10-05-2010, 02:30 PM
  #1  
cjk
Senior Member
Thread Starter
 
cjk's Avatar
 
Join Date: Jul 2010
Location: Cookeville, TN
Posts: 498
Default

I've been asked to make a tut for the frame I made. I've never done one before but I'm going to give it a try.
Ok here goes.
This does include a Flynn frame but I’m sure you could make that to without much trouble. I got it for my birthday and so it didn’t cost me anything.

This is the material list.

This is for a 4’ frame. You can easily make it an 8’ frame.

4 1x2”x8’ poplar boards (if you’re making an 8’ frame you will need 6)

1 ½”x½”x8’ square dowel

1 ¾”x¾”x6’ square dowel

1 1” dowel rod

1 2’ drawer slide (This is what I got, Euro-Style Self-Close Drawer Slide)

4 casters ( I got the stationary kind, They need to be the kind that mount on the bottom)

1 5/8”x12x24” shelf (you could also use plywood)

4 ½” 2 hole pipe strap ( find that in plumbing)

2 clamps

Screws

Nails

Glue

Sand paper

First for the carriage. Take 1 of the 1x2”x8’ boards and cut two 2’ sections Mount your drawer slide to the 2’ sections and your shelf. Make sure you follow the directions on the slides. Cut two 14” sections from the same board. Take the 2 boards that you have the slides on and nail and glue to the 14” boards. Make sure they are square and your shelf slides easily.

Cut the 1” dowel rod into 2 36” pieces. You can make them longer if you want. This should let you sew from both sides. Center and attach the dowel rods to each side of the shelf with the 4 pipe straps. You might have to squeeze them together a little (it’s easy) they need to hold the dowel rod firmly with the straps. Measure the distance between your dowel rods and cut 2 -¾” dowels to fit. Attach to the ends of the dowel rods with a nail and glue or screw.

Attach the 4 casters (wheels) to the bottom of the 14” pieces.

That should have your carriage.
Attached Thumbnails attachment-103868.jpe   attachment-103869.jpe  
cjk is offline  
Old 10-05-2010, 02:33 PM
  #2  
cjk
Senior Member
Thread Starter
 
cjk's Avatar
 
Join Date: Jul 2010
Location: Cookeville, TN
Posts: 498
Default

Now the frame.

Cut 4 - 1x2” 4’ in length.
Cut 2 - 1x2” 2’ in length.
Cut 2 - ½”x½” 4’ in length.

Nail and glue 2 - 1x2” together to form an L.
Nail and glue 1- ½”x½” to form a track.
Repeat for the other side.
Make sure that you check your carriage wheels in the tracks. You don’t want them tight. You just want them as a guide.
Join together at the ends with 1x2”x2’.

I made the side pieces with the scraps. If you’re using the Flynn frame you need to put everything together and set your machine on the carriage. Put the frame in the machine then you can measure how long you need to cut your side pieces. I guess you could measure from the table up to the top of your machine and get the same measurements. But you need to know where to mount your side pieces. So put your frame in and make sure your carriage is as far back as it will go then slide your frame forward to the needle. Now mark on the side of your frame where you want to put your side pieces. Attach your side pieces with nails and glue or screws. Attach the frame to your table with the 2 clamps. There you have it!

Hope this explains ok.
:D
I took these pics after I made it but I hope it helps.
Attached Thumbnails attachment-104252.jpe   attachment-104253.jpe   attachment-104254.jpe  
cjk is offline  
Old 10-05-2010, 02:53 PM
  #3  
Google Goddess
 
Join Date: May 2009
Location: Central Indiana (USA)
Posts: 30,181
Default

Thank you for doing the tutorial for us, great job!

:thumbup: :thumbup: :thumbup:
craftybear is offline  
Old 10-05-2010, 02:54 PM
  #4  
cjk
Senior Member
Thread Starter
 
cjk's Avatar
 
Join Date: Jul 2010
Location: Cookeville, TN
Posts: 498
Default

I hope I made it clear enough
cjk is offline  
Old 10-05-2010, 03:43 PM
  #5  
Super Member
 
Join Date: Feb 2010
Location: Maryland
Posts: 3,586
Default

Thank you, thank you, thank you!
virtualbernie is offline  
Old 10-05-2010, 06:09 PM
  #6  
Power Poster
 
Join Date: Nov 2007
Location: SW Iowa
Posts: 32,855
Default

Thanks for the tute.
littlehud is offline  
Old 10-06-2010, 04:03 AM
  #7  
Super Member
 
finch's Avatar
 
Join Date: Apr 2010
Location: in hiding
Posts: 1,320
Default

That looks fantastic! Great pictures.
finch is offline  
Old 10-06-2010, 06:25 AM
  #8  
PJO
Junior Member
 
Join Date: Mar 2010
Location: Chetopa, Kansas
Posts: 237
Default

Thank you so much! Please tell me what is the size of the throat of the sewing machine you are using on the frame, and how big of a quilt can you quilt on it?

Thanks
PJO is offline  
Old 10-06-2010, 06:33 AM
  #9  
Junior Member
 
Sharoni's Avatar
 
Join Date: Dec 2009
Location: Arkansas
Posts: 195
Default

I'm sorta new to quilting,and I figured someone smarter than me could figure out how to quilt a large quilt on some kind of frame. All I have seen is the humungus quilting machines which totally turns me off. Thanks to you I am now encouraged! You have done it!
Now all I got to do is find someone handier than I to make this for me! Thanks a bunch!
Sharoni is offline  
Old 10-06-2010, 08:31 AM
  #10  
Super Member
 
patdesign's Avatar
 
Join Date: Mar 2010
Location: So. Fla now, Va orig
Posts: 1,565
Default

Im bookmarking this, maybe I can get dh or son to do this for me!
patdesign is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Prism99
Main
32
12-23-2010 12:25 PM
deedles215
Main
16
11-15-2010 02:47 PM
cbuchanan
Main
5
11-12-2010 06:32 PM
Roben
Main
20
09-09-2010 08:50 PM
Bevanger
Pictures
26
07-27-2009 02:46 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter