Go Back  Quiltingboard Forums > Main > For Vintage & Antique Machine Enthusiasts
Fetherweight bobbin winding issue >

Fetherweight bobbin winding issue

Fetherweight bobbin winding issue

Old 11-24-2016, 05:27 AM
  #1  
Senior Member
Thread Starter
 
Join Date: Feb 2007
Location: Westerville, Ohio
Posts: 711
Default Fetherweight bobbin winding issue

I have a black featherweight from 1948. Recently, the bobbin winder seams to have trouble getting going when I start it and when I stop it and start again. It looks like the winder that touches the machine is black plastic. The belt is a fairly new one---bought a year ago but have not been using the machine a lot this last year.
I looked on the featherweight websites and they show mostly metal parts. The plastic wheel is smooth. Not sure what is happening. Yes, I checked how the thread is put through each part to wind bobbin.
Any ideas?
fktsewing is offline  
Old 11-24-2016, 05:42 AM
  #2  
Senior Member
 
Join Date: May 2011
Location: Waynesboro, Tn.
Posts: 932
Default

Check your belt, it may be loose. I got my FW out to take to a class and started to wind a bobbin and it would start and stop. I tightened my belt and was back in business!!!! PM me if you need info on how to DIY.
mawluv is offline  
Old 11-24-2016, 09:18 AM
  #3  
Super Member
 
Join Date: Sep 2015
Posts: 1,963
Default

Is the plastic wheel you describe more a metal wheel with a black rubber tire? That's what I would expect on a Featherweight. It pushes down on the hand wheel, and a few things can make it act up: oil on the rubber or hand wheel, which means wipe it off with a cloth. The rubber tire needs to be replaced sooner or later, but they can easily last a decade or two. There is an oil point in connection with the winder, a tiny hole you might have to poke clean with a tooth pick if it's clogged. The winder should turn very smoothly; if not it'a all about cleaning and oiling. The click action can need attention too, cleaning, oiling and sometimes adjusting (usually only when the tire has been replaced, they are usually not exactly the same width as the old ones). To begin with I would expect it's mostly about cleaning and oiling, but inspect all parts involved.
Mickey2 is offline  
Old 11-24-2016, 11:33 AM
  #4  
Banned
 
Join Date: Aug 2014
Location: Victorian Sweatshop Forum
Posts: 4,096
Default

Mickey FWs don't use a bobbin tire.

Cari
Cari-in-Oly is offline  
Old 11-24-2016, 05:02 PM
  #5  
Senior Member
 
Join Date: Sep 2013
Location: Saskatchewan
Posts: 838
Default

I have to hold my bobbin winder down to get it to work properly. Otherwise it doesn't have enough contact pressure to turn. I suppose there must be a way to fix this, but I haven't figured it out... holding it down is the easy solution.

[ATTACH=CONFIG]562718[/ATTACH]
Attached Thumbnails fw_al5-3.jpg  
Jennifer23 is offline  
Old 11-25-2016, 10:38 AM
  #6  
Super Member
 
Join Date: Jul 2010
Posts: 6,430
Default

I had the same problem with my machine. I discovered that the machine oil had caused the little rollert to become "mushy". A new wheel fixed the problem. Be sure to get a new wheel and be sure to push it down far enough to make contact with the wheel. You shouldn't have to hold it down if you get a new wheel.
carolynjo is offline  
Old 11-25-2016, 12:40 PM
  #7  
Banned
 
Join Date: Aug 2014
Location: Victorian Sweatshop Forum
Posts: 4,096
Default

Originally Posted by carolynjo View Post
I had the same problem with my machine. I discovered that the machine oil had caused the little rollert to become "mushy". A new wheel fixed the problem. Be sure to get a new wheel and be sure to push it down far enough to make contact with the wheel. You shouldn't have to hold it down if you get a new wheel.
Just like I told Mickey in a message above, a FW doesn't use a bobbin tire so it can't get "mushy". In the pic that Jennifer posted, her arrow is almost pointing directly at the little hole on the bobbin winder where a tiny drop of oil should occasionally be added. It sometimes gets all gummed up in there and the bobbin winder doesn't want to spin freely, that's often why the winder doesn't want to wind.

Cari
Cari-in-Oly is offline  
Old 11-26-2016, 10:37 AM
  #8  
Senior Member
Thread Starter
 
Join Date: Feb 2007
Location: Westerville, Ohio
Posts: 711
Default

Ok, DH oiled spot for bobbin winder. He also tightened the belt
the wheel has always spun freely, even before. Should there be tension on the arm itself--it will not stay up
when sewing regularly--tried to tighten screw on left side of winder, but dh cannot budge it at all--should we be able to?
Help is greatly appreciated
fktsewing is offline  
Old 11-26-2016, 11:34 AM
  #9  
Banned
 
Join Date: Aug 2014
Location: Victorian Sweatshop Forum
Posts: 4,096
Default

The belt on a FW should be as loose as it can be without slipping. Any tighter and it puts strain on the motor.

Cari
Cari-in-Oly is offline  
Old 11-26-2016, 07:24 PM
  #10  
Senior Member
Thread Starter
 
Join Date: Feb 2007
Location: Westerville, Ohio
Posts: 711
Default

He did not tighten the belt a lot, just enough as it was slipping
fktsewing is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
AnnieF
For Vintage & Antique Machine Enthusiasts
3
05-05-2016 03:17 AM
Margie07
For Vintage & Antique Machine Enthusiasts
20
01-18-2016 05:08 PM
PghPat
Main
6
08-01-2010 09:40 PM
lfw045
Main
4
05-29-2008 12:45 PM
Donna Mae
Main
5
12-28-2007 07:02 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter