Electrical Zing ....
11-05-2012, 10:35 AM
#1
Junior Member
Thread Starter
Join Date: Sep 2012
Location: Arkansas
Posts: 112
Electrical Zing ....
I think I found the source of the electrical zing whenever I turn on the machine. This is behind where the power cord meets the machine. Now what?!?
[ATTACH=CONFIG]374565[/ATTACH]
[ATTACH=CONFIG]374565[/ATTACH]
11-05-2012, 11:25 AM
#2
Super Member
Join Date: Feb 2012
Posts: 8,091
Rewire time. Or if there is enough extra length put a new end on the bare wire or make a circle connection with it. Just make sure no two wires touch each other ( unless they are supposed to ) or any part of the machine.
Joe
Joe
11-05-2012, 02:24 PM
#5
Junior Member
Thread Starter
Join Date: Sep 2012
Location: Arkansas
Posts: 112
Would the bare wire there be what is causing motor to smoke? Would it be easier to just replace the motor and wiring all together? It may be safer in the long run, maybe?? Can a novice replace motors? I really want to learn how to do this, just scared I guess. That and I don't want a heafty bill!
11-05-2012, 02:40 PM
#6
Super Member
Join Date: Apr 2007
Location: Alturas, CA
Posts: 9,393
Look in the tutorial sectional on here, and you should find at least one by Billy(Lost51, I think) on totally taking your machine apart and putting it back together. The wiring shouldn't be that hard to do, just to give you some encouragement. You can do it!!!!!!!!!!
11-05-2012, 06:14 PM
#7
Super Member
Join Date: Feb 2012
Posts: 8,091
Rewiring a motor is a piece of cake. Rewiring a potted motor is a piece of cake. If you can follow a recipe and bake a cake, or follow the instructions on a pattern and make a dress or a pair of pants, you can follow Rains tutorial and rewire the motor. Just read it first, reread it again, get all the tools and supplies ready ahead of time. And follow it one step at a time.
Newbie, I believe your machine is a 201-2 is it not? If so then the only motors you're going to find are used ones from donor machines. There is an on line store somewhere that sold remanufactured potted motors, but you have to send yours back. I lost that link when my other computer hard drive died.
In a day or two, maybe tomorrow I'm going to do a post on rewiring potted motors. It's not going to be a tutorial as I could never come close to the one Rain did, but some comments and pictures about what I ran into when I just did the one I did. It works pretty good too.
From your picture I can't really tell how bad the wires are on your machine. If you unscrew the single screw at the top center of the cord block and take a picture of the wiring from far enough away to see everything, that would help.
Joe
Newbie, I believe your machine is a 201-2 is it not? If so then the only motors you're going to find are used ones from donor machines. There is an on line store somewhere that sold remanufactured potted motors, but you have to send yours back. I lost that link when my other computer hard drive died.
In a day or two, maybe tomorrow I'm going to do a post on rewiring potted motors. It's not going to be a tutorial as I could never come close to the one Rain did, but some comments and pictures about what I ran into when I just did the one I did. It works pretty good too.
From your picture I can't really tell how bad the wires are on your machine. If you unscrew the single screw at the top center of the cord block and take a picture of the wiring from far enough away to see everything, that would help.
Joe
11-05-2012, 06:35 PM
#8
Junior Member
Thread Starter
Join Date: Sep 2012
Location: Arkansas
Posts: 112
Originally Posted by J Miller
Rewiring a motor is a piece of cake. Rewiring a potted motor is a piece of cake. If you can follow a recipe and bake a cake, or follow the instructions on a pattern and make a dress or a pair of pants, you can follow Rains tutorial and rewire the motor. Just read it first, reread it again, get all the tools and supplies ready ahead of time. And follow it one step at a time.
Newbie, I believe your machine is a 201-2 is it not? If so then the only motors you're going to find are used ones from donor machines. There is an on line store somewhere that sold remanufactured potted motors, but you have to send yours back. I lost that link when my other computer hard drive died.
In a day or two, maybe tomorrow I'm going to do a post on rewiring potted motors. It's not going to be a tutorial as I could never come close to the one Rain did, but some comments and pictures about what I ran into when I just did the one I did. It works pretty good too.
From your picture I can't really tell how bad the wires are on your machine. If you unscrew the single screw at the top center of the cord block and take a picture of the wiring from far enough away to see everything, that would help.
Joe
Newbie, I believe your machine is a 201-2 is it not? If so then the only motors you're going to find are used ones from donor machines. There is an on line store somewhere that sold remanufactured potted motors, but you have to send yours back. I lost that link when my other computer hard drive died.
In a day or two, maybe tomorrow I'm going to do a post on rewiring potted motors. It's not going to be a tutorial as I could never come close to the one Rain did, but some comments and pictures about what I ran into when I just did the one I did. It works pretty good too.
From your picture I can't really tell how bad the wires are on your machine. If you unscrew the single screw at the top center of the cord block and take a picture of the wiring from far enough away to see everything, that would help.
Joe
Hey, Joe. Yes, it is a 201-2. I think I found the link you are referring to. I did bookmark it just in case. The wire doesn't look that bad. I showed my hubby and he is going to try to put new caps on. I will try to get a better pic of the wires for you. If the new caps don't work I will try to follow Rain's tutorial. Thank you so much for all your help.
On refinishing::: The paint is in rougher shape than I originally thought and the decals are pretty worn. Would you refinish it or just let her be as is? I think it gives her personality, but then again she isn't as pretty as I know she can be! Thoughts?
Thread
Thread Starter
Forum
Replies
Last Post
cabbagepatchkid
For Vintage & Antique Machine Enthusiasts
23
10-19-2017 06:42 PM
Dawn227
General Chit-Chat (non-quilting talk)
1
09-20-2011 04:26 AM
