help!! problems cutting

Old 10-21-2011, 03:52 AM
  #11  
Super Member
 
Join Date: Apr 2010
Location: Snellville, Ga & Hiawassee
Posts: 1,994
Default

I've also been having issues with cutting straight strips lately. Just yesterday realized one huge problem- too much INFO! That's right I've been watching & reading about "correct" techniques for cutting. I've been sewing for & quilting for 44 yrs. with good success. Went back to cutting using my "incorrect" technique & wha-la - problem solved.
mimiknoxtaylor is offline  
Old 10-21-2011, 04:35 AM
  #12  
Super Member
 
Join Date: Feb 2011
Location: Carlisle, PA
Posts: 1,964
Default

along with the little dots, I find the suction-cup handle (one you would put on your shower wall as a grab-bar) really helps to stabilize my ruler. They come in different sizes, too. Good luck!
Debbie C is offline  
Old 10-21-2011, 05:55 AM
  #13  
Super Member
 
Join Date: Nov 2008
Location: Central PA
Posts: 3,736
Default

If these are long cuts - do you "walk" your hand up the ruler? That helps to keep it straight.
mimee4 is offline  
Old 10-21-2011, 06:07 AM
  #14  
Super Member
 
Join Date: Jan 2011
Location: Port Ludlow, WA
Posts: 1,379
Default

I had this problem just yesterday, I had the screw on my rotary cutter backwards.
Happy Linda is offline  
Old 10-21-2011, 06:20 AM
  #15  
Power Poster
 
debcavan's Avatar
 
Join Date: Mar 2011
Location: Spring Green,WI
Posts: 14,637
Default

My hands are small so I have problems with the ruler. There is a clear sheet that you can buy that is suppose to help but the smaller the hands, the harder it is. So I have put felt pads every 1 1/2 inches on my ruler just on the edge I use for cutting. It also helps me know which edge to use since my ruler is 8 1/2 inches wide and I want to use the numbers starting with whole inches.

Also I am height impared. This also contributes to the trouble cutting. I am cutting on a table meant for an average sized person. The pads which I get at the dime store or Walmart are very thin and in the department that has the things to put on the bottom of vases and the back of frames.

Some people put on pad at each end. I put them all the way down. it helps my fabric from pushing ahead as I am cutting. Sometimes I just don't get that blade changed and just need to do one cut. That will sound familiar to a lot of us quilters.

I hope you have found a solution that works for you. There are many of us who have solved the individual problem we have.
debcavan is offline  
Old 10-21-2011, 06:34 AM
  #16  
Super Member
 
Join Date: Oct 2010
Location: northern California
Posts: 1,098
Default

There is a new ruler for cutting that has something that pushed down and grabs the fabric... I just ordered it and hope it works. I have arthitis and it hurts to push hard on the ruler. It's called "quilters slidelock", it's not cheap, but for some of us it is worth the cost.
Sierra is offline  
Old 10-21-2011, 06:52 AM
  #17  
k3n
Power Poster
 
k3n's Avatar
 
Join Date: Feb 2009
Location: Somerset, England
Posts: 10,686
Default

Are you splaying your fingers on the ruler, cutting up level and then walking along as others have said? Also, keeping your little finger on the mat NOT on the ruler will stop it slipping.
k3n is offline  
Old 10-21-2011, 07:19 AM
  #18  
Super Member
 
Join Date: Oct 2010
Location: Prescott Valley, AZ
Posts: 1,329
Default

I had that problem until I started putting sandpaper dots on the under side of my ruler. A dot of rubber cement in several places (let it dry good) works also and is less expensive. Then double check that you are using the correct measurement at both ends of the ruler. Put your hand on the end of the ruler closes to you. Cut as far as your finger tips and pause. Move your hand up and cut again as far as your fingertips. Keep going until you've cut all the way across. It seems slow, but you'll get faster and more accurate as you get used to it.
ShirlinAZ is offline  
Old 10-21-2011, 07:31 AM
  #19  
Super Member
 
Join Date: Nov 2010
Location: Florida
Posts: 1,611
Default

Is your ruler slipping around while you are cutting? I had this problem and tried the little dots, walking my hand, etc. none worked. I decided to try weighting it down and used large vegetable cans in plastic baggies so as not to mar the fabric. That was better, but not great because they were hard to manage with my arthritis. My DH suggested using my hand weights and that was the perfect answer for me. The shape of them makes it easy to move them and the weight 3 to 5 pounds are not too heavy.
Another problem was that the rotary blade was not smooth even though it was brand new. I bought another and it is fine. I hope someone's suggestions will help you end this frustrating issue. :)
Tropical is offline  
Old 10-21-2011, 07:56 AM
  #20  
Junior Member
 
Join Date: Jan 2011
Location: MAINE
Posts: 247
Default

I use the sandpaper dots, they work really well at keeping your ruler (s) stationary.
quiltqueen61 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
plainpat
Main
8
02-01-2011 08:21 AM
Janet My
Main
7
12-18-2010 02:36 PM
cminor
Main
10
01-12-2010 03:18 PM
Hycino
Main
23
05-04-2009 02:48 PM
NewsletterBot
Main
4
07-30-2007 04:05 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter