How to Bind a Quilt by Machine
#1
Super Member
Thread Starter
Join Date: Aug 2013
Posts: 9,299
How to Bind a Quilt by Machine
I needed a refresher course to make my machine binding look better. (Normally I hand bind, but occasionally I need to finish quickly.) I found this tutorial especially helpful today. Tried it on my doll quilts and was very pleased with the results.
https://www.youtube.com/watch?v=Wi3yOP8wqa4
https://www.youtube.com/watch?v=Wi3yOP8wqa4
#3
Super Member
Join Date: Jun 2010
Location: The Deep South near Cajun Country, USA
Posts: 5,432
I do mine similar to hers with the exception that I cut my binding at 2.5 inches and don't iron it in half. Then I sew it on the back as she does, including all the corner work. When I turn that binding to the front, I have a little bit extra width. I fold the binding with my fingers and put the edge of my binding on the front so that it just covers the seam that is already there. I then push the extra width of the binding to the back so that now I am sewing on the edge of both the front and the back of binding on the quilt. My stitches do not go off onto the back of the quilt top at all. I work with about 5 inches at a time, using those little red clips to hold everything in place. Those little clips have measurements on them so I can check front & back before sewing and make sure I am where I want to be.
At the corners, I pin like crazy. Yes, I have to rip out stitches sometimes, if my binding slips. Using the clips every 5 inches does help with that. Also, I cut my bindings on the bias so that I can use a little bit of stretch to keep the binding laying flat on the quilt top. Hope this helps someone.
edited to add: I have carpal tunnel in both wrists. Until I figured out how to make the bindings such that they looked like they were put on with a binding machine, but doubled on the edge as they should be, it would take me hours of hand sewing to do the binding on a 60 inch square quilt. Lots of pain too.
At the corners, I pin like crazy. Yes, I have to rip out stitches sometimes, if my binding slips. Using the clips every 5 inches does help with that. Also, I cut my bindings on the bias so that I can use a little bit of stretch to keep the binding laying flat on the quilt top. Hope this helps someone.
edited to add: I have carpal tunnel in both wrists. Until I figured out how to make the bindings such that they looked like they were put on with a binding machine, but doubled on the edge as they should be, it would take me hours of hand sewing to do the binding on a 60 inch square quilt. Lots of pain too.
Last edited by Barb in Louisiana; 11-09-2019 at 09:15 PM.
#4
Super Member
Join Date: Nov 2011
Location: Southern Minnesota
Posts: 4,362
I visited with a lady this summer at a quilt show about this because she said she does both sides with her machine. I mentioned I had tried that way, but never felt I would be happy with it and my finishing the last side by hand always looked much better. I have gotten much quicker at than when I first started. She said the trick was to keep practicing it with the machine and eventually it gets very easy. Hat the idea of ruining my hard work on a quilt by finishing binding by machine if I can't get it right. Maybe I should practice on small projects first, like potholders!
#5
I just made a quilt doing my best to try new things. I did 2 different machine bindings and do not like either one of them. I am sold now on hand stitching any bindings. I figure with all the work I put into making a quilt the last thing I want is to have a bad looking finish to it.
#6
Super Member
Thread Starter
Join Date: Aug 2013
Posts: 9,299
Agreed: Hand binding is my preference for the precision and relaxation of it. But with my additional looming with deadlines , I decided to machine bind. This particular video explains it well . These doll quilts for charity were ideal for practicing. Kids don’t care about the mistakes.
#7
Super Member
Join Date: May 2017
Location: Sunny Florida
Posts: 4,431
I always do machine bindings.
The last two quilts plus a wall hanging were finished with flange binding. I played with strip sizes and the pressing of the seam allowance. On the last one, I used that 1/4 inch seam as the fold line for the flange so it had more definition.
The last two quilts plus a wall hanging were finished with flange binding. I played with strip sizes and the pressing of the seam allowance. On the last one, I used that 1/4 inch seam as the fold line for the flange so it had more definition.
#8
Member
Join Date: May 2013
Location: Canon City,CO
Posts: 53
I use this nifty way to do my binding by machine.
http://valleymqg.org/wp-content/uplo...lt-binding.pdf
http://valleymqg.org/wp-content/uplo...lt-binding.pdf
#9
Super Member
Join Date: Jun 2010
Location: The Deep South near Cajun Country, USA
Posts: 5,432
I use this nifty way to do my binding by machine.
http://valleymqg.org/wp-content/uplo...lt-binding.pdf
http://valleymqg.org/wp-content/uplo...lt-binding.pdf
Thread
Thread Starter
Forum
Replies
Last Post
craftybear
Links and Resources
5
04-25-2011 10:47 AM
craftybear
Links and Resources
1
02-21-2011 08:29 PM