Go Back  Quiltingboard Forums > Main
scalloped borders >

scalloped borders

scalloped borders

Old 03-27-2018, 07:21 PM
  #1  
Member
Thread Starter
 
Join Date: Jul 2016
Posts: 25
Default scalloped borders

I want to try a scalloped border, I can find all kinds of information on how to measure an mark the quilt, how to cut and attach the binding, but how much binding do you make? is there a math formula for it?
Thank you for you help
Granny9 is offline  
Old 03-27-2018, 07:30 PM
  #2  
Super Member
 
Join Date: Apr 2016
Location: Blue Ridge Mountians
Posts: 7,076
Default

The answer is "make too much". Even if you measure around each scallop all around, it hard to calculate how much you loose in each of the "dents" and the diagonal seams. Just measure, get close, and add extra to make too much. remember to make Bias binding for scallops so they lay smooth. Which method are you using? are you following somebody's, like Eleanor Burns you-tube and using her scalloping tool? or some one elses?

Last edited by QuiltnNan; 03-28-2018 at 03:10 AM. Reason: remove shouting/all caps
Jane Quilter is offline  
Old 03-27-2018, 07:30 PM
  #3  
Super Member
 
Join Date: Aug 2011
Location: kansas
Posts: 6,407
Default

Originally Posted by Granny9 View Post
I want to try a scalloped border, I can find all kinds of information on how to measure an mark the quilt, how to cut and attach the binding, but how much binding do you make? is there a math formula for it?
Thank you for you help
I've only done one--would recommend a gentle curve to the scallop (mine was difficult to bind cause so curvy) but since using bias binding, I just made about 25" extra and had plenty.
quiltingshorttimer is offline  
Old 03-27-2018, 08:21 PM
  #4  
Super Member
 
Teen's Avatar
 
Join Date: Dec 2017
Location: Southwest Idaho
Posts: 5,998
Default

Originally Posted by quiltingshorttimer View Post
I've only done one--would recommend a gentle curve to the scallop (mine was difficult to bind cause so curvy) but since using bias binding, I just made about 25" extra and had plenty.
Good advice...gentle curves and extra. I keep any extra binding and use for scrappy binding for future quilts or wall hangings, table runners etc. I do not like running out of binding on quilts. Lol! If it were me, I would measure quilt normally and add on two WOF strips depending on depth of curve.
Teen is offline  
Old 03-27-2018, 08:25 PM
  #5  
Super Member
 
Join Date: May 2011
Location: Pacific NW
Posts: 9,345
Default

Originally Posted by Teen View Post
If it were me, I would measure quilt normally and add on two WOF strips depending on depth of curve.
This is essentially what I did on my scalloped quilt.
Peckish is offline  
Old 03-28-2018, 04:59 AM
  #6  
Super Member
 
Join Date: Oct 2010
Location: Tennessee, UC area
Posts: 1,582
Default

https://ankastreasures.wordpress.com...ding-scallops/ This is a wonderful tute on scallops and binding! I bookmarked to do my next quilt--I love scallops, and I think this is doable.
mermaid is offline  
Old 03-28-2018, 05:04 AM
  #7  
Super Member
 
Join Date: Feb 2011
Location: Yorkville, IL
Posts: 7,639
Default

I added 25 percent and had some left over. Just make sure you use bias binding for curves and it works well. Not the easiest project but so pretty when it is finished!
luvstoquilt is offline  
Old 03-28-2018, 06:16 PM
  #8  
Power Poster
 
Jingle's Avatar
 
Join Date: Dec 2009
Location: Outside St. Louis
Posts: 38,181
Default

Makes a beautiful edging if done right. I am afraid I wouldn't do it right. Maybe later on.
Jingle is offline  
Old 03-29-2018, 01:55 AM
  #9  
Senior Member
 
Join Date: Dec 2016
Location: Upstate SC
Posts: 679
Default

Back when I first learned to quilt and didn't know enough to know I was doing it "wrong"...my first quilt was a Turning Twenty Again king size quilt for my bed. Into the project, Decided I wanted scalloped border on it. I made the border with two layers of fabric about 15" wide,right side together, batting on one side. Marked out the scallops to fit the completed top, stitched the scallops on the border, trimmed, clipped seams and turned so I had a layered scalloped border with an open raw edge that I simply sewed to the finished top (that needed binding). It went on kinda like a big binding. Worked beautifully and I was very proud. Only later did I learn that was NOT the way to do it. But it worked for me and if I decide to put a scallop border on another quilt, I will do it the same way again.
I do not listen to the quilt police!
Murphy224 is offline  
Old 03-29-2018, 03:51 AM
  #10  
Super Member
 
citruscountyquilter's Avatar
 
Join Date: Mar 2013
Location: Hernando FL
Posts: 1,662
Default

I often do scalloped bindings. Make sure you use bias binding and not straight of grain. the more gentle the scallops the easier it is to have nice dips in the scallops. Draw your scallops on your quilt, use this line to put the edge of your binding against, sew your binding on and then cut the scallops away from the quilt. DON'T cut your scalloped edge before you put your binding on. You'll end up with a stretchy edge that is difficult to control.
citruscountyquilter is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Eddie
Tutorials
60
08-01-2011 01:37 PM
Ps 150
Main
4
01-18-2011 09:02 PM
FabricJunkie
Main
4
06-05-2010 08:52 PM
Rebecca
Main
4
10-05-2007 08:06 AM
NewsletterBot
Main
1
06-27-2007 06:08 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter