Go Back  Quiltingboard Forums >
  • Main
  • Binding >
  • Binding

  • Binding

    Thread Tools
     
    Old 11-03-2010, 02:11 AM
      #1  
    Member
    Thread Starter
     
    Join Date: May 2009
    Location: Montana
    Posts: 74
    Default

    What size of binding do you usually put on a quilt? I've heard everything from 2" is the basic to whatever you like. I know the quilt police wouldn't approve, but what does everyone usually like? Also, straight or bias? Just curious.
    gzbird101 is offline  
    Old 11-03-2010, 02:39 AM
      #2  
    Senior Member
     
    BevD's Avatar
     
    Join Date: Jul 2010
    Location: Adelaide, Australia
    Posts: 331
    Default

    I use 2 - 2 1/2 inch depending on how thick my bating is.
    I have always cut it on the straight grain and never had a problem with it.
    BevD is offline  
    Old 11-03-2010, 02:53 AM
      #3  
    Super Member
     
    Join Date: Mar 2010
    Location: North Carolina
    Posts: 2,375
    Default

    2.5" on the grain, with 45 degree connections. I did one that was straight recently, and OMG it made it bulky in those sections. I didn't realize how much that angle helps!
    Rebecca VLQ is offline  
    Old 11-03-2010, 03:01 AM
      #4  
    Super Member
     
    Join Date: Oct 2009
    Posts: 5,453
    Default

    Originally Posted by Rebecca VLQ
    2.5" on the grain, with 45 degree connections. I did one that was straight recently, and OMG it made it bulky in those sections. I didn't realize how much that angle helps!
    that is how i do it too. sometimes i use 2" if i want a thinner /smaller binding.
    i also press the seams open that are on an angle.
    watterstide is offline  
    Old 11-03-2010, 03:32 AM
      #5  
    Power Poster
     
    Join Date: Nov 2007
    Location: SW Iowa
    Posts: 32,855
    Default

    I use 2.5 and connect them at a 45 degree angle. It just seems to be a nice size for me.
    littlehud is offline  
    Old 11-03-2010, 03:38 AM
      #6  
    Super Member
     
    Deecee's Avatar
     
    Join Date: Sep 2009
    Location: Victoria, Australia
    Posts: 3,724
    Default

    Originally Posted by littlehud
    I use 2.5 and connect them at a 45 degree angle. It just seems to be a nice size for me.
    Ditto.
    Deecee is offline  
    Old 11-03-2010, 03:44 AM
      #7  
    Super Member
     
    k9dancer's Avatar
     
    Join Date: Aug 2010
    Location: Mena, Arkansas
    Posts: 1,351
    Default

    I use anything from 2.5" to 3.5," with 3" being my usual.
    Strips are cut cross grain, just like any other strips I would use in my quilt. I fold down one corner into a point on each strip, press, and use the fold as my seam line when joining at a 45 degree angle. Baste first, to make sure the strips are lined up properly; then stitch & trim the seam. I start in the middle of a side, leaving a good 6" hanging loose. Stitch to within 1/4" of a corner, backtack & remove. Miter corner & begin again. When I get to the starting side, I leave plenty of room to manipulate my binding so I can line it up, mark with chalk, and again make that 45 degree seam. It's more important to baste this last bit than the initial diagonal seams. Then I flip to the other side and finish by hand.
    k9dancer is offline  
    Old 11-03-2010, 03:58 AM
      #8  
    Senior Member
     
    Joeysnana's Avatar
     
    Join Date: Mar 2010
    Location: Indiana, PA
    Posts: 983
    Default

    Originally Posted by Rebecca VLQ
    2.5" on the grain, with 45 degree connections. I did one that was straight recently, and OMG it made it bulky in those sections. I didn't realize how much that angle helps!
    that happened to me, too. I will stick with the diagonal join from now on.
    Joeysnana is offline  
    Old 11-03-2010, 04:11 AM
      #9  
    Super Member
     
    justwannaquilt's Avatar
     
    Join Date: Aug 2009
    Location: Union, Missouri
    Posts: 1,542
    Default

    Originally Posted by Rebecca VLQ
    2.5" on the grain, with 45 degree connections. I did one that was straight recently, and OMG it made it bulky in those sections. I didn't realize how much that angle helps!
    Me too, except I use 2 inch strips on the grain.
    justwannaquilt is offline  
    Old 11-03-2010, 04:55 AM
      #10  
    Super Member
     
    Connie in CO's Avatar
     
    Join Date: Jul 2010
    Location: Canon City, Colorado
    Posts: 2,419
    Default

    I use 2 1/4 with straight of grain
    Connie in CO is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    craftybear
    Links and Resources
    0
    11-03-2011 01:23 PM
    hlponyfarm
    Main
    65
    06-24-2011 11:10 AM
    MaryAnna
    Tutorials
    30
    12-12-2010 08:06 AM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is On
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter