Log Cabin Strips
#3
Super Member
Join Date: Aug 2010
Location: Northern California, Sonoma Co.
Posts: 2,814
Personally, I like logs that are 1-1.5" finished. I don't like them much wider or much narrower than that, but that's just my preference. I also like them all the same width, although varying the width within the block can do some interesting things to the block. Like this, as shown by the very talented QB member Barnbum:
http://www.quiltingboard.com/picture...o-t137116.html
http://www.quiltingboard.com/picture...o-t137116.html
#5
For a traditional log cabin I make the strips 1" finished, and I cut them to length before sewing them together. For an offset log cabin, I use strips that are 1" finished on one side and .5" finished on the other. But... I have seen beautiful log cabin quilts with strips that are much, much wider.
#6
Senior Member
Join Date: Jun 2011
Location: Orlando, FL
Posts: 416
I have not made a log cabin but I helped my daughter to make one when she was ten. I like the look of the narrower strips better. She used the the method where you cut your first piece (for the center) and then sew it onto a long strip for the second piece and then cut the second piece to length. When she was all finished some of the blocks were as much as 1/2 to 3/4 inch bigger than the others.
So based on that experience I would recommend the following:
1. Measure each block as you finish to ensure that it is the correct size.
2. Double check the seam allowance as you sew (this plays into Step 1.)
3. I would probably cut the strips to the needed log length.
So based on that experience I would recommend the following:
1. Measure each block as you finish to ensure that it is the correct size.
2. Double check the seam allowance as you sew (this plays into Step 1.)
3. I would probably cut the strips to the needed log length.
#7
When I made a scrappy log cabin I used different size strips. Just make sure the same size is used in all the same rounds. Important to even up each round as you go. I have made log cabin blocks that give a measure for each length of rounds.
The scrappy I cut length to fit.
The scrappy I cut length to fit.
#8
Super Member
Join Date: Apr 2010
Location: Illinois
Posts: 9,312
Personally I like the look of narrow strips... I use a 1 1/2 inch cut , the colors just seem to melt into each other. It is faster to use the wider strip cut. If you want a curved look to your piece... use a wider strip on one side and a narrow on either the dark or the light side. You get a nice appearance of a curve if there is 1/2 inch difference in the width cut from the dark to the light. So when I make a "curved" log cabin I cut the dark 1.5 inches and the light 1 inch.
#9
Power Poster
Join Date: Feb 2009
Location: Northern Michigan
Posts: 12,861
the width of the strips are a personal choice- I just finished a top with 2" wide logs (1 1/2" finished) and it is pretty wonderful! I do cut my logs the length I need them to be- I've tried a few times to leave them long & cut them off as I went- I did not have great success with that method. my blocks were more consistent when I measured, cut then attached each log as I went- I did work on all 30 blocks at once- so I would add a log to each block, press, measure for the4 next log, cut 30 of them- go back to the sewing machine- it worked well & went faster for me than some other times I've made them.
#10
Power Poster
Join Date: Jul 2009
Location: Between the dashes of a tombstone
Posts: 12,716
I do as lakekids. I'm a pretty controlled log cabin maker in regards to size as you can see in my avatar quilt, but I had some odd width strips and made these free wheeling courthouse steps.[ATTACH=CONFIG]449880[/ATTACH] Nice for me to get out of my box now and again.
In a "normal" log cabin varying the size of beginning square can change the look of the block as well.
In a "normal" log cabin varying the size of beginning square can change the look of the block as well.
Thread
Thread Starter
Forum
Replies
Last Post
justflyingin
Main
37
04-19-2011 08:43 PM