Go Back  Quiltingboard Forums >
  • Main
  • How to Fussy Cut >
  • How to Fussy Cut

  • How to Fussy Cut

    Thread Tools
     
    Old 08-24-2010, 12:58 PM
      #1  
    Super Member
    Thread Starter
     
    Join Date: Apr 2010
    Location: New York City UWS
    Posts: 4,222
    Default

    Any tips?
    I'm trying to cut 4 1/2 " squares from a tight repeat.
    I do not have a handy 4 1/2 " piece of acrylic! Thanks so much
    dotcomdtcm is offline  
    Old 08-24-2010, 01:09 PM
      #2  
    Power Poster
     
    Join Date: May 2008
    Location: MN
    Posts: 24,645
    Default

    I cut a 4.5 inch square from template plastic

    then I put 1/4 inch masking tape around the edges to "frame" the cutout

    (or you could just mark a "seam line" on the template

    cut your first piece

    if you are OCD - you can cut your first square - then lay the cut square on the next "cutting site" - line up the pattern - and cut them one by one -

    This is one place/time where I do think starching/sizing before cutting is worth the effort.
    bearisgray is offline  
    Old 08-24-2010, 01:29 PM
      #3  
    Super Member
    Thread Starter
     
    Join Date: Apr 2010
    Location: New York City UWS
    Posts: 4,222
    Default

    Where do I get template plastic? My LQS? Thanks
    dotcomdtcm is offline  
    Old 08-24-2010, 01:30 PM
      #4  
    Member
     
    Join Date: May 2010
    Posts: 67
    Default

    OK, this is definitely not as easy as having the perfect template but it will work.

    Take any square, relative clear template that is larger than 4.5" and mark off two sides of the square with tape. I often use Scotch tape that I place so that the middle of the tape is about where the exact measurement should be and then mark the tape with the exact measurement with a bright colored Sharpie pen marker.

    To cut, pick your fussy spot, cut the two sides that the square template defines, rotate/move the template and line up your tape marks with the cuts, and cut the final two sides.

    The problem with this method is that since you have to move the template, the final patch is more to prone to error.

    When completely done cutting all of your squares, remove the tape and your template is good as new.
    Spydee is offline  
    Old 08-24-2010, 01:51 PM
      #5  
    Banned
     
    Join Date: Aug 2010
    Posts: 2,047
    Default

    I use a clear acrylic square, take a marker and outline (on the acrylic) the pattern (or select areas of)
    then I can place it in the exact position on next piece.
    Lady-T is offline  
    Old 08-24-2010, 02:32 PM
      #6  
    Senior Member
     
    DoxieMom's Avatar
     
    Join Date: Jul 2010
    Location: Central Florida
    Posts: 535
    Default

    I'd suggest cutting out a 4 1/2" square opening in a piece of thin, but stiff, cardboard. Use the opening to mark a square on the fabric and then cut. Once the first one is marked/cut, use the corners of it to exactly locate/mark the corners of each additional square. Be careful to not enlarge the opening of your template while marking the fabric. (You might have to make several identical cut-out templates if you're marking a lot of squares...) I used this method to fussy cut a circle for the center of a Wagon Wheel block and it worked really well. I could see exactly what the piece looked like before I marked it and cut it. Good luck with your quilt!
    DoxieMom is offline  
    Old 08-24-2010, 02:36 PM
      #7  
    Super Member
     
    Join Date: Jan 2010
    Location: West Coast
    Posts: 9,267
    Default

    Originally Posted by DoxieMom
    I'd suggest cutting out a 4 1/2" square opening in a piece of thin, but stiff, cardboard. Use the opening to mark a square on the fabric and then cut. Once the first one is marked/cut, use the corners of it to exactly locate/mark the corners of each additional square. Be careful to not enlarge the opening of your template while marking the fabric. (You might have to make several identical cut-out templates if you're marking a lot of squares...) I used this method to fussy cut a circle for the center of a Wagon Wheel block and it worked really well. I could see exactly what the piece looked like before I marked it and cut it. Good luck with your quilt!
    yes, I've done this in a pinch with good results.
    DebraK is offline  
    Old 08-24-2010, 02:47 PM
      #8  
    Super Member
    Thread Starter
     
    Join Date: Apr 2010
    Location: New York City UWS
    Posts: 4,222
    Default

    Thanks everyone.
    dotcomdtcm is offline  
    Old 08-24-2010, 06:25 PM
      #9  
    Super Member
     
    pab58's Avatar
     
    Join Date: Jun 2010
    Location: near Tucson, Arizona
    Posts: 5,841
    Default

    I had my sweetie make a "window" template for me out of heavy cardboard. I included the seam allowance, and then traced around the inside of the window. It works extremely well! :wink:
    pab58 is offline  
    Old 08-24-2010, 06:26 PM
      #10  
    Super Member
     
    pab58's Avatar
     
    Join Date: Jun 2010
    Location: near Tucson, Arizona
    Posts: 5,841
    Default

    I had my sweetie make a "window" template for me out of heavy cardboard. I included the seam allowance, and then traced around the inside of the window. It works extremely well! :wink:
    pab58 is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    sharon b
    Main
    14
    06-06-2010 12:09 PM
    Jingle
    Main
    9
    12-27-2009 12:01 AM
    sondray
    Links and Resources
    0
    12-08-2009 09:48 AM
    Dingle
    Main
    8
    11-29-2009 04:40 PM
    Jaynie
    Pictures
    15
    03-09-2009 09:19 AM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is On
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter