Go Back  Quiltingboard Forums > Main
Help!  Turning the handle on a quilt bag >

Help! Turning the handle on a quilt bag

Help! Turning the handle on a quilt bag

Old 05-12-2015, 01:17 PM
  #1  
Power Poster
Thread Starter
 
Join Date: Jun 2011
Location: Southern California
Posts: 19,131
Default Help! Turning the handle on a quilt bag

I am having difficult pressing the seams flat on a handles for these quilted Bible Bags that are going with our missionaries to the Philippines again this fall I am just getting an early start. The handle is a cut 2.5" x 28" and I fuse interfacing inside before turning. But I can't figure out how to get that seam pressed flat when turn right side out so I can have it place on the side. I looked for some bias pressing bar but none were wide enough. When I press the seam flat, there seems to appear some wrinkles caused by the interfacing moving. I stuck a large wooden knitting to press the seam flat but concern about getting burned with the iron. Any suggestion??

Also if anyone can come up with simple pattern that I can make the pattern into 3" finished blocks, I would appreciate any suggestion. The size of the unfinished bag is 12.5" x 18.5"

THANKS !!
Attached Thumbnails bible-bag-handles.jpg   sq-sq-bible-bag.jpg  
ManiacQuilter2 is offline  
Old 05-12-2015, 01:25 PM
  #2  
Super Member
 
Join Date: Aug 2010
Location: Slidell, Louisiana
Posts: 6,951
Default

Hey ManiacQuilter, I can't help with the sizes, but for the handles, I would just put the interfacing on the wrong side of the fabric strip, press sides in to center, then fold in half and stitch instead of trying to turn inside out.
Oh, love the bag, pretty. Love the square in a squares too.

Last edited by Latrinka; 05-12-2015 at 01:32 PM. Reason: forgot something!
Latrinka is offline  
Old 05-12-2015, 01:34 PM
  #3  
Member
 
Join Date: Dec 2010
Location: Connecticut
Posts: 15
Default

Latrinka, that is the way I do it but I make the strips 4" and the interfacing 3" so that when I turn them in twice, the width of the handle is about 1.5". I've given up trying to turn the handles on bags.
dommiesewing is offline  
Old 05-12-2015, 01:47 PM
  #4  
Super Member
 
Buckeye Rose's Avatar
 
Join Date: Jan 2011
Location: Monroe, IN
Posts: 2,283
Default

When I make totes/handbags, I use a 5" strip the desired length....press in half, wrong sides together, lengthwise...then open up the strip, bring the long edges to the crease and press again....then fold in half along original lengthwise crease and stitch 1/4" from each long edge....no turning required, simple and fast.
Buckeye Rose is offline  
Old 05-12-2015, 02:10 PM
  #5  
Power Poster
 
Join Date: Dec 2010
Location: Michigan
Posts: 11,276
Default

What Latrinka said. I have also had issues doing it the way you have described. I also have better luck with a stiffer home dec type NON fusible rather than a soft batting. Using a fusible makes the process less forgiving because the fabric is trapped by the adhesive.
As far as the 3" blocks are concerned, how about if you used two 9" (finished) blocks, then put a 3" X 18.5" solid strip on the bottom? You could coordinate the bottom fabric with the handles. You would need to seam the bottom so the sides come out on the seam between the blocks, not the center of a block as in your top photo.
Or you could also use two 6 inch blocks surrounded by 3" plain strips, then seam the bag as in your top photo so the plain strips are on the sides. Sorry about defacing your beautiful square in square example, but this is what I am thinking of
:[ATTACH=CONFIG]519504[/ATTACH]
Quilter's Cache is organized by block size so you can easily find blocks of appropriate size.
Attached Thumbnails suggesst.jpg  
PaperPrincess is offline  
Old 05-12-2015, 02:10 PM
  #6  
Super Member
 
franc36's Avatar
 
Join Date: Dec 2010
Location: Tennessee
Posts: 1,501
Default

Originally Posted by Buckeye Rose View Post
When I make totes/handbags, I use a 5" strip the desired length....press in half, wrong sides together, lengthwise...then open up the strip, bring the long edges to the crease and press again....then fold in half along original lengthwise crease and stitch 1/4" from each long edge....no turning required, simple and fast.
That is the way I make my tote bag handles. I agree with Buckeye Rose that it is simple and fast. Also, the handles look good and hold up well. In addition to the 1/4" stitching down the sides, I stitch down the middle.
franc36 is offline  
Old 05-12-2015, 02:27 PM
  #7  
Power Poster
 
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 41,444
Default

Before turning right side out, try a wooden broom handle (or length of dowel)and see if it will fit down inside it. Iron the seam open before turning and once ironed open, put a few dabs of glue stick along the seam allowance and press again to dry the glue. Turn the tube right side out and if necessary, put the broom handle back inside and press again.
Tartan is offline  
Old 05-12-2015, 06:39 PM
  #8  
Super Member
 
Girlfriend's Avatar
 
Join Date: Sep 2012
Location: San Clemente, CA
Posts: 1,211
Default

Your batiks are gorgeous!!

When I make handles, I sew 2 - 2 1/2" strips, plus one strip of batting of your choice. The 2 fabrics are right sides together and the batting on the bottom. Sew all the way down both sides. To turn the handles, I use a 4" very large safety pin (blanket pin) from Joann's. Pin one edge, stick it through the hole, and start pushing and gathering until you can pull the safety pin through the other end. Iron flat, stitch 1/8" from each side. They always turn out great! Good luck with your bags. What a great thing you are doing.
Girlfriend is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
gingerd
Main
6
03-19-2012 01:57 AM
Stitchnripper
Pictures
18
06-30-2011 06:16 PM
AngieS
Pictures
40
11-19-2010 07:54 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter