Go Back  Quiltingboard Forums > Main
Piecing warn and natural batting >

Piecing warn and natural batting

Piecing warn and natural batting

Thread Tools
 
Old 12-04-2010, 03:53 PM
  #11  
Senior Member
 
yolanda's Avatar
 
Join Date: Mar 2010
Location: Southern California
Posts: 927
Default

Oh! I used some Heat Press Batting Tape and it works great! I also used this stuff to patch some vintage blocks that were really weak. Here is a link: http://www.heatpressbattingtogether.com/

My friend The Batty Lady sells this online but I've not checked her prices.

Originally Posted by vicki s
What is the best way to piece warm and natural batting together. Do you butt it together and zig zag or just put it in the quilt and be sure to anchor it good when quilting. Have lots of larger pieces but not quite big enough. Thanks. Vicki
yolanda is offline  
Old 12-04-2010, 03:54 PM
  #12  
Cyn
Super Member
 
Join Date: Aug 2010
Location: Jacksonville NC
Posts: 6,510
Default

Butt together and zig zag has always worked well for me.
Cyn is offline  
Old 12-04-2010, 04:50 PM
  #13  
Power Poster
 
dunster's Avatar
 
Join Date: Mar 2009
Location: Lake Elsinore, CA
Posts: 15,143
Default

I used to overlap the two pieces slightly, then use a rotary cutter to make a wavy line through them, then use needle and thread to whip the two pieces together - no overlap. However, last time I butted the two pieces together and used the thinnest fusible interfacing to join them. I cut the interfacing into 1.5" strips, laid it on the batting where the two pieces came together, laid a strip of cotton on top of that, and pressed with a hot iron. I did it on my cutting table, since it is much longer than my ironing board. I have that batting in a quilt on the longarm now, and the seam is hanging tight and close. I will use this method again next time. (This is for cotton batting, not for poly.)
dunster is offline  
Old 12-04-2010, 07:19 PM
  #14  
Super Member
 
Join Date: Feb 2010
Location: lexington ky
Posts: 1,418
Default

I actually have done both
katiebear1 is offline  
Old 12-04-2010, 07:47 PM
  #15  
Senior Member
 
QuiltQtrs's Avatar
 
Join Date: Mar 2010
Location: NW Arkansas
Posts: 984
Default

Use your Walking Foot, butt edges together.
QuiltQtrs is offline  
Old 12-04-2010, 07:48 PM
  #16  
DJ
Super Member
 
Join Date: Mar 2008
Location: Pacific NW
Posts: 4,392
Default

Originally Posted by ktbb
there are several ways - I overlap the pieces slightly then run a rotary cutter down thru the doubled portion - when I throw away the scrappy edges that have been cut away, I then have two perfectly matched cut edges, and I butt them up against each other and use the widest zig=zag to stitch them together...no double thicknesses of batting to deal with in the final product..and I don't have to tug and push the edges to match.
Just what I do, but I use the 3-step zig zag. Works great.
DJ is offline  
Old 12-04-2010, 08:01 PM
  #17  
Junior Member
 
quiltnutt's Avatar
 
Join Date: Apr 2010
Location: South Florida
Posts: 116
Default

I use my velvet foot aka joining foot to piece the batting together.
This foot has a wall in the middle of the foot. You place the batting one piece on either side of the wall. Use a large zig zag stitch to piece.
The wall keeps the batting from overlapping and a ridge will not appear.
I use this all the time for my quilts and charity quilts.
quiltnutt is offline  
Old 12-04-2010, 08:12 PM
  #18  
Super Member
 
amandasgramma's Avatar
 
Join Date: May 2009
Location: La Pine Oregon, USA
Posts: 5,907
Default

I just longarmed a quilt where the owner had pieced the warm and natural with a zig zag.....just PLEASE use thread that matches the warm and natural!!!! They used GREEN thread on part of it...I didn't realize it until it was too later. I white piece on the front shows the green thread behind!!!!! ARRRRGH
amandasgramma is offline  
Old 12-05-2010, 04:45 AM
  #19  
Senior Member
 
Join Date: Jul 2010
Location: Wisconsin
Posts: 502
Default

I found some fusible lightweight interfacing at Joanne's and cut it with the rotary cutter in 1 1/2 inch strips to use for piecing batting, should work on Warm and Natural too. Much cheaper than the precut tape. Or is you have some from sewing, use it up this way.

Carol J.
Carol J. is offline  
Old 12-05-2010, 05:14 AM
  #20  
Super Member
 
JAGSD's Avatar
 
Join Date: May 2010
Location: South Dakota
Posts: 1,216
Default

Originally Posted by Carol J.
I found some fusible lightweight interfacing at Joanne's and cut it with the rotary cutter in 1 1/2 inch strips to use for piecing batting, should work on Warm and Natural too. Much cheaper than the precut tape. Or is you have some from sewing, use it up this way.

Carol J.
Thanks for this hint, I to have used the precut roll of fusible and thought it was expensive, this sounds super!
JAGSD is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
kim_s
Main
16
11-21-2012 09:53 AM
Christine-
General Chit-Chat (non-quilting talk)
30
07-07-2012 11:51 PM
dreamer2009
General Chit-Chat (non-quilting talk)
5
04-04-2011 09:52 AM
aneternalpoet
Pictures
110
11-30-2010 11:58 AM
MissTreated
General Chit-Chat (non-quilting talk)
59
07-17-2010 04:25 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



FREE Quilting Newsletter