Quiltingboard Forums

Quiltingboard Forums (https://www.quiltingboard.com/)
-   Main (https://www.quiltingboard.com/main-f1/)
-   -   Basic maintenance for Janome 6600 (https://www.quiltingboard.com/main-f1/basic-maintenance-janome-6600-a-t167737.html)

Buckeye Rose 11-11-2011 05:06 PM

Basic maintenance for Janome 6600
 
I recently purchased a used 6600 and absolutely love it! I've been through the operators manual, paying attention to the maintenance section. I have taken apart the bobbin area, cleaning it well a couple times. The manual says nothing about oiling anything, but I don't want to mess up this machine by neglecting something I need to be doing. If I need to be oiling it, what kind of oil do I use? Is there anything else that I am missing?

QuiltE 11-11-2011 05:40 PM

You have me curious too! I must remember to ask my dealer.

Dolphyngyrl 11-11-2011 05:43 PM

most computerized machine come oiled, anything like that is handled by dealers for high end machines

Shelbie 11-11-2011 05:55 PM

I have a Janome 6500 and it has an oil wick under the bobbin case in a small hole. Nowhere in the manual does it say to oil it in this spot but my bobbin case was rattling, growling and jumping out of place. It jumped out of place so badly that I eventually put my machine needle right through the case and my dealer kept telling me that it was operator error!!!! I finally found out about this spot after reading the Janome 6500/6600 on-line forum. After oiling it in that little hole, my machine went back to sounding and stitching normally. Now I just add a drop of oil there any time my machine starts to sound noisy.

scowlkat 11-11-2011 06:02 PM

Shelbie is correct about the wick under the bobbin case. My dealer told me to try one drop and if it absorbs quickly, try a second drop. If it doesn't soak completely in, use a piece of cloth to get the excess out. The other locations that need to be oiled are internal and are taken care of during your yearly maintenance. I have done this myself on the 6500 but don't think it would be a good idea on the 6600 unless you have okayed it with your dealer. (Most dealers won't tell you anything about doing the oiling yourself.)

tootskellett 11-11-2011 06:08 PM

You need to remove the bobbin case and clean out the lint from underneath it. (use a soft brush or pipecleaner). Then you can put One drop of sewing machine oil on the "wick". It looks like a small round spot of lint under the bobbin case. (do not pull it out) .When you replace the bobbin holder make sure that the red marks line up with each other. None of the other parts need any oil. It is suggested that you put this drop of oil on the wick when it appears to be dry. Also clean out this area quite often - e.g after 6-8 hours of sewing, and before starting a new project.
I hope this helps.

Buckeye Rose 11-11-2011 06:41 PM

what kind of oil? Brand? and thanks for the help!

wvdek 11-11-2011 07:19 PM

When I purchased my Janome, the dealer told me NOT to oil my machine. He said for the newer computerized ones, it was not necessary and that it could actually gunk it up. However, because I live 2 hours from him, he did show me where I could oil if it really needed it. I have had the machine about 4 years and have never oiled it, I clean it often (especially the bobbin area), change my needle with almost every new project. Still have not had to have it serviced. I did have to replace the bobbin holder after a thread nest caught the spring and broke it. Otherwise, I have not even had it serviced. Still runs smooth as long as I follow my manual and not what I want to do.
That said, if your machine has been stored in a dry place, it could be more dry than usual. I would contact a dealer or go on Janomes website. Contact a professional who deals with it daily. Too expensive a machine to be messing it up.

EasyPeezy 11-11-2011 09:58 PM

I use Kenmore sewing machine oil. If you just bought your machine you probably don't need to oil it unless it's starts getting noisy.

quilterella 11-12-2011 03:06 AM

I have had my Janome 6600 for 7 years and it has been serviced once(only because I thought it died...needed two new fuses). The guy who did the maintenance on it said "Not to oil it, he had only put 1 drop on the wick. He also said, as long as we continue to clean out the bobbin area(even beneath the racer), that that was the only maintenance we should have to do, as they will check the oil needs when doing the service job. But like I said, 7 years later and 1 drop of oil. What a great machine!!!!


All times are GMT -8. The time now is 11:32 PM.