Quiltingboard Forums

Quiltingboard Forums (https://www.quiltingboard.com/)
-   Main (https://www.quiltingboard.com/main-f1/)
-   -   Dealing with the elusive 1/4" seam... (https://www.quiltingboard.com/main-f1/dealing-elusive-1-4-seam-t322296.html)

Iceblossom 01-25-2024 09:01 AM

I've always maintained that sewing is a physical activity, maybe small muscle but still there is hand/eye coordination and other things at play. You can't just get up and play professional sports, and (most of us!) can't do professional sewing results unless we practice practice practice. I just took about 18 months off after daily sewing for years, and it has taken me some time to get back to where I want to be. When I first switched from garment construction to quilting, the 1/4" seam seemed so impossibly small... but after time it starts seeming rather large and accommodating and you can tell if you are right on or big or small.

You said you've tried some of the seam guides, what I had on my vintage machine was an adhesive bandage, several inches from the needle near the edge. I took a piece of graph paper and put the needle through it and used that for placing the bandage. The visible guide of the plastic helped, as did the little hump of fabric. Nowadays I'm a big fan of the 1/4" foot and use it many ways.

It didn't occur to me for years (decades even) to square up my sub-units, I'd just fit them in as they were. When I decided to start checking them anyway, I slowly made the shift away from trying to be very precise with my cutting and my sewing to doing the cut large and trim down. Might as well make it worth my time to check by doing some trims, and it is happier and easier for me not so tense. While trimming can be boring and it feels like it takes a lot of time, I feel it evens out in the next step, no fitting in just nice straight cuts to deal with. If it is just a couple of threads I don't bother but often there is more, especially since I tend to sew scant anyway.

For those that know me, I was not very appreciative of what I originally called "fabric wasteful techniques" but I did a few tests and found that I really don't waste much fabric. Typically whatever I was cutting had a couple inches left from the row that now accommodates the slightly larger pieces. Even on very busy queen sized quilts, I don't think I've ever needed more than one extra row of fabric.

Any time you are doing modern strip piecing techniques or trimming down, you should use a rather small stitch, at least 12 per inch. I think I'm usually in the 16 range -- it makes it really hard with my vision issues to take out stitches so I still try and be precise but know I can be a speed demon when I want to be.

Sadly there is no one "right" way to cut large, we each have our own techniques. Square units are easy for most of us. Pieced triangles are often easiest to have one cut as normal and others cut larger. To help with the trimming I use tape to mark the lines on my rulers. There are many brands of 1/4" tape and I always have a roll in my sewing kit.

quiltsfor 01-26-2024 04:14 AM

I like to use presser feet that match what the seam size I want, by using presser feet with a guild or compensating presser feet.

I have been using presser feet with a seam guild on them and have a good selection of different seam widths for both the left and right sides, depending on which way I am sewing the seam. I recently found that one of my sewing supply places Cutex Sewing Supplies, carries a set of 8 different sizes of compensating presser feet in a set, one set of 8 or right side and one set of 8 for the left side, for a good price and I liked the sizes.

I'm finding that I prefer the compensating presser feet better than those with the attached seam guide as it fits closer to the base of my sewing machine and it keeps the fabric from dipping under the 'guide' better. I like the different sizes for doing applique, edge sewing on my binding, and regular piecing of blocks. I don't have any problem with getting the seam size sewn that I want, no matter what width I'm using.

I also square up each process of piecing my blocks, and between the two, presser feet and squaring up, I don't have any issue with matching up my blocks, or losing points on design features.

Peckish 01-26-2024 07:33 AM

I wonder if it's not the seam allowance, but pressing with steam. Is it possible that your fabric is shrinking?

OurWorkbench 01-26-2024 07:47 AM


Originally Posted by quiltsfor (Post 8633722)
I like to use presser feet that match what the seam size I want, by using presser feet with a guild or compensating presser feet.

I have been using presser feet with a seam guild on them and have a good selection of different seam widths for both the left and right sides, depending on which way I am sewing the seam. I recently found that one of my sewing supply places Cutex Sewing Supplies, carries a set of 8 different sizes of compensating presser feet in a set, one set of 8 or right side and one set of 8 for the left side, for a good price and I liked the sizes....

Just a note about the set of 8 is for high shank machines. https://www.cutexsewingsupplies.com/...32221481828405
https://www.cutexsewingsupplies.com/...32221481697333

quiltsfor 01-26-2024 11:38 AM

This is one of the reasons I love having a high shank machine. There are so many presser feet that you can find for the high shank machines, that aren't made or sold for the low shank, and/or clip-on presser feet machines. And others like the Bernina Machines, their presser feet are really neither high or low shank, so you have to get the Bernina brand if you buy presser feet.


All times are GMT -8. The time now is 07:56 AM.