Always lose my points, help!!!
#1
Super Member
Thread Starter
Join Date: Jan 2011
Location: Small town in Northeast Oregon close to Washington and Idaho
Posts: 2,795
Always lose my points, help!!!
I have been quilting since 1992 and have quilted many, many quilts and my favorite block is the star block. But I lose my points every time. I'm doing a star block right now and stomped out of the sewing room in frustration because I am losing my points. I don't know what I am doing wrong. Lately, I've been avoiding anything with points, but then I narrow my selection of patterns quite a bit. I follow the direction correctly. I mean, all my other parts of the quilt are fine. Please tell me what I'm doing wrong.
#3
Super Member
Thread Starter
Join Date: Jan 2011
Location: Small town in Northeast Oregon close to Washington and Idaho
Posts: 2,795
I'm waiting for my new camera so I can take pictures but I'll tell you that I only have less than quarter inch from my points to the edge of my fabrics and when I sew the fabrics together, it takes away a little bit of the point
#4
Power Poster
Join Date: Dec 2010
Location: Northern California mountains
Posts: 12,538
I am guessing you are making an 8 point "sawtooth" star. The most common reason for point cut offs is seam allowances not being uniform. What I was taught to do is check every allowance as you go along until they are regularly right. I generally make my sawtooths with HST blocks, although it is just as easy beginning with flying geese. I cut my HST's 1" larger than the finished size I want. This gives me 1/8" for trimming, after I press and use starch or sizing. When I use the square over a rectangle method, I need to remember to be 1 thread width off the center line with my sewing. Pressing is very important here too.
#5
Super Member
Join Date: Apr 2010
Location: Brady TX
Posts: 6,613
They say that a picture is worth a thousand words. Well here are some picts of some of my pinwheels. As you see I try to cross my intersections. Even where the points go further into the seam allowance.
[ATTACH=CONFIG]290756[/ATTACH] [ATTACH=CONFIG]290757[/ATTACH][ATTACH=CONFIG]290759[/ATTACH][ATTACH=CONFIG]290760[/ATTACH][ATTACH=CONFIG]290758[/ATTACH]
Don't pay attention to the glue where I used it instead of pins. It will wash out.
This is Turtle, my quilt inspector. He had to make sure that I took the right pictures!
[ATTACH=CONFIG]290756[/ATTACH] [ATTACH=CONFIG]290757[/ATTACH][ATTACH=CONFIG]290759[/ATTACH][ATTACH=CONFIG]290760[/ATTACH][ATTACH=CONFIG]290758[/ATTACH]
Don't pay attention to the glue where I used it instead of pins. It will wash out.
This is Turtle, my quilt inspector. He had to make sure that I took the right pictures!
#6
I match the points with a pin checking to make sure the pin is exactly at the points of both pieces. Sew right up to the pin where you know it is matched. either take the pin out at this point or hand crank it over the pin if you are sure the needle won't hit it. This has made it much easier for me to get sharp points.
#8
I match the points with a pin checking to make sure the pin is exactly at the points of both pieces. Sew right up to the pin where you know it is matched. either take the pin out at this point or hand crank it over the pin if you are sure the needle won't hit it. This has made it much easier for me to get sharp points.
#9
Banned
Join Date: Mar 2010
Location: Sturbridge, Ma
Posts: 3,992
check to make sure you are maintaining the correct seam allowance to the end. Use a sharp point to hold the fabric so the seam allowance doesn't shift. I find this is the most common problem causing points not to match.
Thread
Thread Starter
Forum
Replies
Last Post
tropit
Mission: Organization
70
03-04-2017 10:18 PM
tothenci
Links and Resources
6
06-22-2012 10:15 AM