Is there a foot to achieve a SCANT 1/4 inch seam??
#51
Originally Posted by watterstide
Originally Posted by incoming2me
I have several low shank machines and use this foot for all my piecing.
I don't think I could piece without it!
I don't think I could piece without it!
this foot has the single hole..so if you move your needle to far, you could break the needle or worse,bend the shaft.
However, my low shank machines are vintage Singers and only have a straight stitch..
no optional needle positions. :)
#54
Senior Member
Join Date: Mar 2011
Location: Michigan
Posts: 757
I was taught by a quilting teacher to buy the thick "mole skin" pad that is found in the Dr. Scholl's area of your local store. It comes in a rectangle that's about 1 and1/2" x 3". It is sticky on one side. Cut out a strip along the 1&1/2" side that's about a 1/4" wide. I use a ruler and my rotary cutter to get a straight, clean cut. This gives you a small "wall" to lay down on your scant quarter inch line from your foot toward you on your machine. Then, when you are piecing, just line the edge of your fabric with that edge while you are sewing. The thickness of the "skin" makes it so that your fabric stays inside that line. I hope this is making sense to you. It works really well, and when your skin starts to wear out, you can pull it off. You will have plenty of extra to keep cutting more pieces.
OOPS! Just realized that the reply above said the same thing! Sorry for the repetition!
OOPS! Just realized that the reply above said the same thing! Sorry for the repetition!
#55
Senior Member
Join Date: May 2010
Posts: 466
Originally Posted by LoriJ
I use the Angler 2 from Pam Bono. It goes out far enough to the front that I can line up a scant 1/4 inch very easily. My piecing is perfect when I use it.
http://pamsclub.com/index.php?catego...hk=1&Itemid=71
http://pamsclub.com/index.php?catego...hk=1&Itemid=71
#57
Super Member
Join Date: Dec 2009
Location: Ohio
Posts: 2,929
Originally Posted by GagaSmith
I have a Janome 6300 and I adjust the width to 4.5 and use the 1/4 inch foot and it gives me a scant 1/4 inch.
It's just where you can adjust the stitch length and width. I assume your machine has that feature.
It's just where you can adjust the stitch length and width. I assume your machine has that feature.
#58
Originally Posted by Greeter Eva
Originally Posted by LoriJ
I use the Angler 2 from Pam Bono. It goes out far enough to the front that I can line up a scant 1/4 inch very easily. My piecing is perfect when I use it.
http://pamsclub.com/index.php?catego...hk=1&Itemid=71
http://pamsclub.com/index.php?catego...hk=1&Itemid=71
#59
Originally Posted by piepatch
You can get a magnetic seam guide at Hancock's that is "thick" enough to keep your fabric from shifting over it. It is better than using a post it note, or tape or moleskin. Of course your machine base would have to be metal for the magnetic guide to hold. I have only seen them at Hancock's, but you might find them in other fabric shops.
http://www.hancockfabrics.com/Magnet...VVviewprod.htm
http://www.hancockfabrics.com/Magnet...VVviewprod.htm
#60
Super Member
Join Date: Oct 2009
Posts: 5,453
The magnet on the bottom of the machine, or on the bed, is no where near the "brain" of the machine. it would do no harm there.
they now have magna-hoops for the bernina Emb sewing machines..
Just be careful if you have a computerized machine. While it may not actually cause any damage, chances are pretty good that if it did, you are out good money to have it fixed.
they now have magna-hoops for the bernina Emb sewing machines..
Originally Posted by cattailsquilts
Originally Posted by piepatch
You can get a magnetic seam guide at Hancock's that is "thick" enough to keep your fabric from shifting over it. It is better than using a post it note, or tape or moleskin. Of course your machine base would have to be metal for the magnetic guide to hold. I have only seen them at Hancock's, but you might find them in other fabric shops.
http://www.hancockfabrics.com/Magnet...VVviewprod.htm
http://www.hancockfabrics.com/Magnet...VVviewprod.htm
Thread
Thread Starter
Forum
Replies
Last Post