Go Back  Quiltingboard Forums > Pictures > Mission: Organization
Tips to make old desk into quilting table >

Tips to make old desk into quilting table

Tips to make old desk into quilting table

Old 05-09-2012, 03:52 AM
  #21  
Senior Member
 
Join Date: Dec 2010
Location: Martensdale, Iowa
Posts: 319
Default

What you could do. The middle area where you chair goes into you could put one of those sliding shelve units in. What I am talking about is the kind they use in kitchen cabinets where the shelve slide out.
The best solution to the problem is cut the legs off. My husband has to cut down every cabinet I get because they are just to tall for me.
grandmahoney is offline  
Old 05-09-2012, 04:08 AM
  #22  
Member
 
Join Date: Sep 2011
Posts: 9
Default

Raise your chair, then add a footrest to keep your legs at a comfortable level. This would have to be custom made to suit you, and don't forget to make sure the foot pedal has room as well. Good luck!
roxanneleblanc is offline  
Old 05-09-2012, 04:55 AM
  #23  
Junior Member
 
Drw52372's Avatar
 
Join Date: Nov 2010
Location: Minnesota
Posts: 161
Default

Here is instructions from Quilt in a Day on how to turn an farm table into a sewing table. I'm sure it would work the same for your desk. http://www.quiltinaday.com/freepattern/
Drw52372 is offline  
Old 05-09-2012, 06:03 AM
  #24  
Senior Member
 
MdmSew'n'Sew's Avatar
 
Join Date: Nov 2011
Location: a small village about 65 miles north of NYC
Posts: 551
Default

Since the el piece is the right height, I would see if someone could move the drawer to the left side of the desktop (most of these pieces are modular, so moving the drawer may not be a problem), then turn it so the desk is along the left wall and the el section is where the desk now sits - a lot easier than cutting and fussing, you'd still have the extra space while quilting, wouldn't lose the storage space in the drawer, and a whole lot easier, I would think. If you were piecing, your machine could be anywhere on the el work space, so you have plenty of room to manage all the pieces, etc. around the machine as you work, if you were quilting, you could move it so it was right on the edge where the two pieces come together, so the quilt doesn't fall into a chasm and get bunched up. Or maybe just move it closer to the joint, and add a phone book or something to make a 'bridge' to the desktop. Just not my phone book, it's about 6x8" and 3/4" thick - will be good for strip piecing but not much use when trying to create height!

Last edited by MdmSew'n'Sew; 05-09-2012 at 06:07 AM.
MdmSew'n'Sew is offline  
Old 05-09-2012, 06:03 AM
  #25  
Super Member
 
MaggieLou's Avatar
 
Join Date: Apr 2010
Location: Central Florida
Posts: 1,804
Default

I have an old executive desk I use as a sewing table. I can use the center drawer to put my machine in and it's pretty much level with the desk top. It also has two pull out shelves on each side. I've debated about having my DH cut a section out of the top for my machine but I would hate to lose the top of the desk. If you cut a hole in the desk top, make sure you cut it a little larger than you need and mount a shelf to sit your machine on just deep enough to keep your machine level with the desktop. Use the piece you cut out to replace in the desktop if you move your machine. That way you still get the use of a level desktop without a hole in it.
MaggieLou is offline  
Old 05-09-2012, 11:39 AM
  #26  
sap
Junior Member
 
Join Date: Dec 2010
Location: mid MI
Posts: 288
Default

I think Elenor burns has a video on how to convert an old kitchen table to hold a maching flush w the tyable top. that might help u w your problem.
sap is offline  
Old 05-09-2012, 03:53 PM
  #27  
Gay
Super Member
 
Join Date: May 2012
Location: S.E. Queensland, Australia
Posts: 1,448
Default

Why not raise your chair to a suitable height, then use a box or footstool to put the foot pedal, and your feet on, so they are not uncomfortable. Glue a bit of velcroe to the bottom of the pedal, and perhaps fabric to the box to stop sliding.
Gay is offline  
Old 05-10-2012, 07:07 AM
  #28  
Super Member
 
Caswews's Avatar
 
Join Date: Feb 2011
Location: Quilting, crocheting, sewing and crafting in my Sewing Room...Peaceful and wonderful !!
Posts: 5,317
Default

Thanks I have an L shaped computer table I use as my quilting/sewing area and had been thinking of doing the drop down item for the machine. This just might help ! Thanks for sharing
Caswews is offline  
Old 05-10-2012, 07:58 AM
  #29  
Senior Member
 
Join Date: Sep 2011
Location: Central NY
Posts: 859
Default

My husband just modified a garage sale table for me like this: He cut a hole to fit my machine. He took a board a little bigger than the hole and using carriage bolts hung it right under the hole. These carriage bolts are long enough, 4"-5" or so, to make the shelf adjustable for any machine. They do show on the top of the table but are rounded smooth and shiny. They could be recessed into the top, but I didn't want him to bother with that. He cut 1" off the legs because I'm short. The shelf adjusts with bolts and there are rounded caps on the ends so nothing will catch on them.

We are looking for another cheap ($20 or so)table or two so he can modify some to sell. We're hoping to get $75-$100 for a nice big sewing/quilting table. I live in Central NY.
Wintersewer is offline  
Old 05-10-2012, 12:50 PM
  #30  
Super Member
 
Country1's Avatar
 
Join Date: Dec 2010
Location: Bowling Green, KY
Posts: 2,441
Default

Wouldn't that weaken the table and possibly make it lean in that area?
Country1 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
grandmasieg
For Vintage & Antique Machine Enthusiasts
7
07-03-2014 05:59 AM
Wanabee Quiltin
Main
9
01-17-2013 08:36 PM
Scissor Queen
Mission: Organization
21
07-06-2012 06:31 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter