Binding Table Runner
1 Attachment(s)
I have never made anything with an uneven border. How would you put the binding on this table runner?[ATTACH=CONFIG]416288[/ATTACH]
|
I am not a huge fan of the birthing method but in this case, I think it would be the way to go. You lay the runner face down on top of the backing fabrics that is face up and have the batt on the bottom. Sew all around the edges leaving a small section open the turn right side out. Trim around the edges, turn and then quilt. I think Jenny Doan has a similar design runner but with bigger squares that she birthed on her MSQC youtube videos. OR you could try to put binding on but I don't recommend it in this case.
|
Tartan, that is exactly what I was going to say!!!!
|
Tartan and Alikat are right! Jenny Doan has a tutorial that shows exactly what to do:
http://www.youtube.com/watch?v=-i_RVyvIxXM |
Thank you all for your suggestions and tutorial. The only problem is that I have already quilted the piece. Is there any other way to bind it or should I remove the quilting. I did quilting in the ditch around each square.
|
This is similar to birthing a quilt. Lay the quilted runner face down on a piece of fabric and sew around the edges. Cut out a rectangle in the center of the facing fabric, leaving about 1" at the narrow spots. Clip and trim and turn the facing to the back of the quilt. Finish the facing by turning under 1/4" and sewing down.
|
exactly as Tartan says. Too diff. otherwise
|
Tartan has it right.
|
if it's already quilted, you could still birth it with another piece of fabric and do some additional light quilting to hold that on. binding inside and outside points is doable, but is a pain.
|
Originally Posted by QuiltnNan
(Post 6095363)
if it's already quilted, you could still birth it with another piece of fabric and do some additional light quilting to hold that on. binding inside and outside points is doable, but is a pain.
ITA with so many before, while I am not a fan of the birthing method, this is one time where it is called for! |
nice colours
and thanks for all of the info. |
If it is already quilted, you can do a facing. You will need to cut strips the width of the outside triangles that are beyond the edge with about an inch extra. Sew the strips to each edge following the zig zags, clip and trim and turn the strips to the back. You then hand stitch the raw edges under to the back of the runner. Look for a video on doing quilt "facings."
|
Just a thought. If you decide to make another tablerunner like this one, you may want to do 'Prairie Points' for the edging. The points will be complete when you add them to the top and it will be a lot easier to finish this way. Just a thought. I like it, like the bright colours, very summery. Thank you for sharing.
|
You can bind this but you will definately want to use bias cut binding. There's a tute somewhere that would help you. I'll see if I can find it for you.
http://ankastreasures.wordpress.com/...e-your-skills/ http://m.youtube.com/#/watch?v=4VGNc...%3D4VGNcDoI-R8 http://m.youtube.com/#/watch?v=Be9dz...%3DBe9dzI_X41w http://www.thatgirlthatquilt.com/201...-tutorial.html |
Just got this from All Free Sewing, seems to be just what you are looking for.
http://www.allfreesewing.com/Sewing-...-Hexagons/ml/1 |
I think the easiest way now is to tuck-iron and sew. Use a blanket binding stitch and hopefully it won't ripple.
|
Janie, Since you have already quilted this runner, you might want to watch this video as I think this is what you probably can do at this point. It looks fairly straightforward although a bit tedious but since your piece is a table runner and therefore not too big, it might work for you. Good luck with your very cheery runner! I could have used that on my table in February when it was so dreary.
http://quilting.wonderhowto.com/how-...-edges-232952/ |
I would do it with bias binding as it would allow more give going around the points. Have done one table runner that had curved and pointed pieces and it worked fine with that.
|
Originally Posted by alikat110
(Post 6095035)
Tartan, that is exactly what I was going to say!!!!
|
All times are GMT -8. The time now is 07:16 AM. |