Featherweight Bobbin Case Removal
I have a featherweight with thread jammed behind the bobbin case base. I've tried everything in order to remove it. I'm able to remove the gib screw and the gib moves out, but the bobbin case base won't slide to the proper position in order to remove it. I've tried heat and a lot of oil, but the bobbin case base won't budge. Anyone have any ideas on this?
|
I wish I could help..... sounds like you are more knowledgeable than I. I have 2 FWs but haven't had this happen to me so I'll be watching to see what advise you get.
|
Are you sure you removed all the screws attaching the bobbin assembly to the shaft? If so, you can squirt a little WD40 or liquid wrench into the area to see if it loosens it up. Be sure to wipe off any excess and don't let it get on any paint.
|
Lynn,
Go here http://thefeatherweight221factory.co...MachineJam.php for a how-to on clearing thread jams. It looks like he's had to redo his sit as the pics don't show up. But he does have very concise instructions on how to do it. Joe |
I know how to remove the bobbin case base because I've done it on other featherweight machines. The problem is I can't rotate the bobbin case base around to the point where it can be removed...it won't budge. I've removed the gib screw and pulled the gib out. Thanks for the advice, but I think this one is going to be very difficult. I just hope I can eventually accomplish it. Maybe someone else has some ideas...I hope.
|
I had this happen on my FW. I could undo the gib screw and take the gib out but couldn't go any further. I finally was able to wiggle (gently) and pull the thread out. NOW, though, I can't get the bobbin case/gib lined back up correctly. The needle hits "something" when I turn the hand wheel. I took a pic and will post it to see if anyone can figure out what I'm going wrong. I have the manual and it "seems" to be lined up correctly. She's just sitting waiting on me to get her to feeling better!! When I get frustrated, I tend to walk away and it takes me a while to get back to it.
|
Originally Posted by Nanamoms
(Post 5188392)
I had this happen on my FW. I could undo the gib screw and take the gib out but couldn't go any further. I finally was able to wiggle (gently) and pull the thread out. NOW, though, I can't get the bobbin case/gib lined back up correctly. The needle hits "something" when I turn the hand wheel. I took a pic and will post it to see if anyone can figure out what I'm going wrong. I have the manual and it "seems" to be lined up correctly. She's just sitting waiting on me to get her to feeling better!! When I get frustrated, I tend to walk away and it takes me a while to get back to it.
|
What and where is the gib screw? Is there a picture?
|
2 Attachment(s)
My featherweight would not take up the bobbin thread and the top thread kept getting wound around the back of the bobbin. I started researching on the QB and web as to how to take it apart. As I started to examine the parts of my bobbin base, I found that the little "thingy" that fits up where the needle comes down is broken off! I think you can see in the picture where it is broken off.
[ATTACH=CONFIG]412187[/ATTACH] [ATTACH=CONFIG]412188[/ATTACH] I found one on eBay for (just the base) for $39.00. One site wanted $238.00 for the whole thing. Glad I just found the base! |
Can't remove bobbine case base either!!
Originally Posted by Surfergirl
(Post 5187603)
I have a featherweight with thread jammed behind the bobbin case base. I've tried everything in order to remove it. I'm able to remove the gib screw and the gib moves out, but the bobbin case base won't slide to the proper position in order to remove it. I've tried heat and a lot of oil, but the bobbin case base won't budge. Anyone have any ideas on this?
Not sure I wanna do that. ANYBODY, have another idea? Thanks |
All times are GMT -8. The time now is 07:57 AM. |