Quiltingboard Forums

Go Back  Quiltingboard Forums >
  • Search Forums
    • Reload this Page >

  • Search Results

    • Register
    FAQ
    Calendar
    Today's Posts
    Search
    Vendor Directory
    Search: Posts Made By: Suziebee
    Showing results 1 to 9 of 9
    Search took 0.00 seconds.
    Forum: For Vintage & Antique Machine Enthusiasts
    12-16-2018, 10:19 AM
    Replies: 27
    Views: 11,358
    Posted By Suziebee

    Would you post a picture with the cabinet open? I...

    Would you post a picture with the cabinet open? I would like to see how that cabinet works.

    Thanks
    Forum: For Vintage & Antique Machine Enthusiasts
    11-28-2018, 12:47 AM
    Replies: 10
    Views: 7,776
    Posted By Suziebee

    You should also put a new needle on it. This...

    You should also put a new needle on it. This fixes a lot of problems too.
    Forum: For Vintage & Antique Machine Enthusiasts
    11-02-2018, 03:48 PM
    Replies: 4
    Views: 4,092
    Posted By Suziebee

    Since I couldn't find a replacement light, I...

    Since I couldn't find a replacement light, I spent some time removing all the old duct tape goo. After that I was able to take the light fixture apart. The wire is riveted in place, but my husband...
    Forum: For Vintage & Antique Machine Enthusiasts
    10-28-2018, 05:12 PM
    Replies: 4
    Views: 4,092
    Posted By Suziebee

    There doesn't seem to be a way to replace the...

    There doesn't seem to be a way to replace the wire as there is no way to get to the connection. The plastic socket is broken with pieces missing. The place where the mounting piece fits into the...
    Forum: For Vintage & Antique Machine Enthusiasts
    10-28-2018, 03:00 PM
    Replies: 4
    Views: 4,092
    Posted By Suziebee

    Necchi BU Nova - Need light!

    I recently picked up a Necchi BU Nova, circa 1953.
    The light fixture had duct tape on it and cracked wire insulation. Any ideas were I can find an replacement or equivalent? I have already...
    Forum: For Vintage & Antique Machine Enthusiasts
    10-14-2018, 05:38 AM
    Replies: 9
    Views: 3,912
    Posted By Suziebee

    There are a few clips on the front edge, probably...

    There are a few clips on the front edge, probably from being thrown into the dumpster. It was very dirty on the outside. Looked like it had been sitting in a garage or basement for sometime. I...
    Forum: For Vintage & Antique Machine Enthusiasts
    10-13-2018, 12:18 PM
    Replies: 9
    Views: 3,912
    Posted By Suziebee

    Yes, I watched that video. We adjusted the...

    Yes, I watched that video. We adjusted the height of the pin/shaft that holds the cam stack by adjusting the screw that is under by the light. Stack was reinstalled. I put everything back...
    Forum: For Vintage & Antique Machine Enthusiasts
    10-13-2018, 03:35 AM
    Replies: 9
    Views: 3,912
    Posted By Suziebee

    The other Slant Needle I have is a 403a with the...

    The other Slant Needle I have is a 403a with the removable top cams, so there isn't a cam stack to compare it too. With my husbands help I think we have figured out how to adjust the height of the...
    Forum: For Vintage & Antique Machine Enthusiasts
    10-08-2018, 04:13 PM
    Replies: 9
    Views: 3,912
    Posted By Suziebee

    Singer 401A Rescue

    I recently rescued a 401A from a trash pile. I have another slant needle and thought I could use parts off of it. When I got it home, I cleaned it up because it didn't look too bad. I used TriFlow...
    Showing results 1 to 9 of 9


     
    Forum Jump

    FREE Quilting Newsletter