Paula R

I am making a bargello quilt using the "tube" method. I have sewn my strips together but when I connect the last two strips together it is all out of whack. Just wondering if anyone has any ideas on how to keep my seams from being "stretched" so the last two will meet up correctly. Thanks for any input!!

crashnquilt

I starch my fabrics. If I'm working on a quilt that has tiny pieces I heavily starch the fabrics. I don't use BEST PRESS, canned starches, or sizing. I purchase STA-FLO in a large bottle and mix it myself and put it into a spray bottle. I use a 50/50 mixture. Yes, I do get "flakes" but those brush off easily. You must iron the fabric dry. I do not use steam in my iron when I use starch. I get a much better starch set this way. Here is what I would do in your situation:
Starch fabric before cutting
Make strips, starch, iron in the tube
CAREFULLY remove stitches between selected pieces to prevent stretching
If the strip is narrow I would starch again
When working with small pieces, instead of ironing the length of strip I would iron side to side and move strip

I find that by starching my fabrics and piecing as I go along I get more accurate seams and the fabric is easier to work.

Tashana

Spray starch and changing the direction in which you join the strips works for me. The last two seemed always to be a challenge untill I decided to piece them in smaller amounts. Join all strips in pairs, than join pairs, than join sets of four and so On. Clear as mud? I hope it helps!

HilaryK8

I didn't starch mine but you have to match up every single seam. I made the mistake of mixing batiks with LQS printed fabric and el-cheapo fabric. Some fabrics were looser or stretchier than others. So you have to butt up your seams as you're sewing. Sometimes periodically pinning helps. But once you're off on one seam all the others are off unless you compensate. And I agree with Tashana, join 1/2 then 3/4 then 5/6 etc. I labeled EVERYTHING with painters tape. The tape didn't come off until the whole top was finished.

DogHouseMom

Yes to starch ... especially if you are working with narrow strips (many strips in my avatar finish at 1/4").

Yes to sewing each strip in the opposite order. To make sure I know which order I sewed the previous strip - I leave the leading thread tail on the strip. I always know where I started (those ends are going to be lopped off anyway!).

Some of the problem could also be uneven feed while your sewing (the feed dogs pull the bottom fabric faster than the top fabric feeds - resulting in a slight shift of the top fabric forward). Pinning helps. I use a dual feed walking foot to piece which helps immensely.

Make sure your seams are UNIFORM. Whether uniform 1/4" or uniform scant 1/4" ... as long as it's uniform throughout the whole strip. Eyeball it before you press it. If you see a place where it is off ... rip it and fix it. If you are sewing narrow strips as much as 1/16" will throw the balance off.

Ironing the strips is of key importance!! You have to make sure the seam remains straight when you iron the seams. For me, I can iron a long strip straighter if I iron the seams open as opposed to ironing to one side. I will lay the strip down and fingernail press the seam open first, then press it open first on the inside then again on the outside.

After you sew EVERY STRIP re-measure the piece to make sure that the width of the combined strips is even and straight. If not, rip it and fix it as it will give you grief if you don't. Check for bowing or slanting to one side.

Good luck!

Lori S

Yes starch really really helps( I do this prior to cutting) ... and I do press my seams open rather than to one side.. When you get to the final tube seam... do not use the raw edges of the first and last strip to line up for that last seam. Lay the strip set down( prior to the last seam) and line up the seams at the ends disregard where you started to sew the seams as your guide or the ends where you will make your colum cuts ( at this point) ... its highly unlikely they will line up. Once you have the seams lined up and everything is laying flat.... then pin and sew. Trim off the wonky part of the beginning of the strip set.
I use 1/2 width cuts of the fabric for my bargellos... so much easier to work with escpecially when it comes to getting that last seam .. and trying to line it all up and lay flat. Full lenght strip sets always will get some bit twist ( for me at least).

quiltsRfun

Thanks for the interesting and helpful thread. I'm getting ready to start a bargello (my first) so I appreciate all the suggestions.

Claire1128

When you're sewing strips and come to the end of a strip reverse direction. That will ensure the strips will line up properly.

gigigray032447

I hate starch and never use it. I've also made many bargellos. If you "make" your last two strips come together you are going to have bigger problems down the road. Don't try to force it, just sew it as best you can. You will lose the fabric on each end as you cut cross ways of the fabric. If you force the seam, you will wind up with diagonal pieces, not squares, which you can't pin out as you sew the rows together. They will always look like a diagonal.

Somewhere on my home computer I have basic instructions, with a lot of pictures, I would be happy to email you. My quilty friend who sews far more than I do had never made a bargello. I taught her how using email. PM me if you are interested.

DDuMouchel

I'm in the middle of a very complex bargello right now. I'm finding it very helpful to cut my strips parallel to the selvedge (in other words, NOT the way it comes off the bolt.) The strips are shorter but much less stretchy.