Go Back  Quiltingboard Forums >
  • Main
  • For Vintage & Antique Machine Enthusiasts
  • 301A to FMQ -- Hot foot pedal -- what to do?? >
  • 301A to FMQ -- Hot foot pedal -- what to do??

  • 301A to FMQ -- Hot foot pedal -- what to do??

    Old 04-24-2013, 07:55 AM
      #1  
    Senior Member
    Thread Starter
     
    Join Date: Mar 2012
    Location: Usually in my sewing room
    Posts: 813
    Default 301A to FMQ -- Hot foot pedal -- what to do??

    I've been using my 301A to FMQ, mainly just stippling. Problem I have is that my foot pedal gets so hot that I have to quit and let it cool off. Should I invest in a different pedal? What is the cause?
    Stitch124 is offline  
    Old 04-24-2013, 07:57 AM
      #2  
    Super Member
     
    Join Date: Oct 2011
    Location: dallas tx.
    Posts: 5,172
    Default

    I don't know. Mine get too hot too. They're very old. I just go take a break and get back to them.
    barny is offline  
    Old 04-24-2013, 11:14 AM
      #3  
    Super Member
     
    Join Date: Feb 2012
    Posts: 8,091
    Default

    Those old foot controllers are resistance units. They use wire or carbon pile resisters to control the voltage. When you sew slowly for an extended amount of time, they get hot. I have several like that. I use silicone iron pads between them and my carpet and like barny said, I sometimes have to stop and take a break. Since I usually sew bare foot I can tell pretty quick when they get hot.

    About the only cure is to replace the old controller with an electronic unit. They don't get hot at all. But they are amp sensitive so you have to make sure the controller is rated for the same or higher amp rating as the motor on your machine. Also my only real gripe on the electronic units is they are lightweight plastic and tend to scoot out from under my foot. The factory electronic controllers are better made if you can find one.

    Joe
    J Miller is offline  
    Old 04-25-2013, 04:41 AM
      #4  
    Senior Member
    Thread Starter
     
    Join Date: Mar 2012
    Location: Usually in my sewing room
    Posts: 813
    Default

    Joe - could you provide the name of a factory electronic controller? I'd like to get one siince this is my main sewing machine for FMQing and I have lots of quilts to do. Don't want to burn my tootsies!
    Stitch124 is offline  
    Old 04-25-2013, 04:59 AM
      #5  
    Super Member
     
    Join Date: Feb 2012
    Posts: 8,091
    Default

    Stitch,

    Well not exactly but most of the machines since the 80s use them. Our mid 80s 4622A has an electronic controller on it. The controller is labeled Singer and it's a bit more substantial than the aftermarket units.

    Another idea is to go to you LSMG and see if he'd have a used one. Or an online Singer factory parts source.

    Joe
    J Miller is offline  
    Old 04-25-2013, 05:27 AM
      #6  
    Super Member
     
    Glenda m's Avatar
     
    Join Date: Oct 2010
    Location: Oklahoma
    Posts: 1,131
    Default

    Since I have three of these lovely machines, I just switch cords and don't have to stop. LOL I know, that's cheating, but when you are on a roll, who wants to quit?
    Glenda m is offline  
    Old 04-25-2013, 05:35 AM
      #7  
    Power Poster
     
    ube quilting's Avatar
     
    Join Date: Jul 2010
    Location: PA
    Posts: 10,703
    Default

    As an aside, back when these machines were in regular household use they were probably not used as much for FMQ and so there wouldn't be this situation happening. As others have said, take a break from the machine.
    peace
    ube quilting is offline  
    Old 04-26-2013, 10:21 AM
      #8  
    Super Member
     
    ArchaicArcane's Avatar
     
    Join Date: Jul 2012
    Location: Not Here
    Posts: 3,817
    Default

    Joe - Put a piece of velcro on the bottom of the foot, cut a piece of wood to size, put the other part of the velcro on that, and stick the two together. Maybe a little felt on the bottom to save the floor. Velcro lets you move one board from pedal to pedal.

    Stitch124 - Hot is "ok", obviously not desirable, unplug it and let it cool then it will be fine to use but if it ever starts making popping sounds, unplug it immediately and don't use it until it's properly repaired.

    It means the pedal is adjusted wrong and it may start a fire. I've had 3 now that have done it. The first one was before I started seriously working on machines. Scared the beans out of me. The second was about 3 weeks ago, on a featherweight I went to look at. The machine started humming as soon as it was plugged in, and after a few seconds, started sewing by itself. Within about 2 minutes, it was popping and fizzing. Yes, I brought the poor lady home. The last one was this week. I took it completely apart, cleaned every carbon disk, and reassembled. It's a nice "mildly warm" running pedal now.
    ArchaicArcane is offline  
    Old 04-27-2013, 11:22 AM
      #9  
    Super Member
     
    citruscountyquilter's Avatar
     
    Join Date: Mar 2013
    Location: Hernando FL
    Posts: 1,662
    Default

    Mine has gotten hot too and I discovered that where I was using it it was resting on thick pile carpeting. Once I took it off the carpeting to sew it helped to a great extent. I just set the foot controller on s thin book. The hard surface allowed air to circulate around the bottom of the foot control. I also limited the time I FMQ to 20-30 minuted at a time and laid the foot petal on it's side to cool off faster when I was done. I was using a machine from 1977. Probably the newer machines have something that takes care of that.
    citruscountyquilter is offline  
    Old 04-27-2013, 11:53 AM
      #10  
    Super Member
     
    Join Date: Sep 2009
    Location: Massachusetts, USA
    Posts: 1,775
    Default

    Originally Posted by ArchaicArcane
    I took it completely apart, cleaned every carbon disk, and reassembled. It's a nice "mildly warm" running pedal now.
    Do you use just a damp Q-tip or do you use something else to clean it with?
    cabbagepatchkid is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    Sarabela
    For Vintage & Antique Machine Enthusiasts
    9
    11-29-2014 08:27 AM
    joobee
    For Vintage & Antique Machine Enthusiasts
    9
    04-07-2014 06:04 AM
    Treasureit
    Links and Resources
    56
    07-21-2013 07:33 AM
    cminor
    Main
    56
    05-21-2013 11:16 AM
    Monie
    Main
    20
    09-23-2011 05:35 AM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is Off
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off


    FREE Quilting Newsletter