Help with Free-motion quilting Breaking too many needles
#21
Senior Member
Join Date: Aug 2007
Location: Frankfort, Ky.
Posts: 797
I read all the other suggestions and they are right on. Here's another one. Does your machine have a 1/2 speed or can you adjust the machine speed. Remember to bring up your bobbin thread and when you start sewing don't jerk to get started. Make you some quilt sandwiches and practice first, then move on over to your project. Relax and enjoy your creativity.
#24
I also have a husquvarna and had the same problem with the needle and the thread, tried all I could think of as well as the problem solver section in the handbook. It turned out to be the thread, was using gutterman varigated @ $13.99 for 300yrds. But it could be worse the machine could have been at fault.
Another thing that can happen is if you move your hands faster than the needle is going you will break needle as it gets pulled to the side and hits the needle plate. hope this helps.
Another thing that can happen is if you move your hands faster than the needle is going you will break needle as it gets pulled to the side and hits the needle plate. hope this helps.
#26
good suggestions ... the bigger needle (and, just because a needle is new, doesn't mean that the needle doesn't have burrs - - nothing is perfect <g>)
The hopping/darning/embroidery foot (and, I found out that if you don't lower the presser foot, even though it isn't touching the fabric, your life won't be worth nothin'! <g>)
And, slowing down ... not moving your hands as fast as the machine is going ... a little like patting your head and rubbing your tummy, but a consistent, moderate speed will make a nice stitch, (a good tip even for those of us with stitch regulators )
And, bring your bobbin thread up to the top of the quilt BEFORE you take off quilting ... it is the only way I know of to avoid a rat's nest in the back, and if you have never had one - - you will ... even quilting machines require that one step ...
Enjoy! <wave>
The hopping/darning/embroidery foot (and, I found out that if you don't lower the presser foot, even though it isn't touching the fabric, your life won't be worth nothin'! <g>)
And, slowing down ... not moving your hands as fast as the machine is going ... a little like patting your head and rubbing your tummy, but a consistent, moderate speed will make a nice stitch, (a good tip even for those of us with stitch regulators )
And, bring your bobbin thread up to the top of the quilt BEFORE you take off quilting ... it is the only way I know of to avoid a rat's nest in the back, and if you have never had one - - you will ... even quilting machines require that one step ...
Enjoy! <wave>
#27
What stitch length are you using? I had been told to set it at 0 now that really broke my needle a lot as I was trying to move the quilt while the needle was down. I change it to 2 and it works great but I am still afraid to FMQ because I hate the needle breaking sound - I scream and my dog runs through the house barking and this wakes my husband - that opens a whole can of different issues. Good luck Emily
#29
Originally Posted by Extreme Quilter
My bobbin winder on my Viking Designer I sometimes winds threads too tightly. If I happen to be free motion quilting quickly, the bobbin thread pulls on the needle and causes it to break. If I unwind a few inches of thread from the bottom and cut it off, I'm sometimes lucky enough to reach a part of the bottom that has been wound better and then my fmq goes smoothly. If not, I change my bobbin and try again.
#30
I just finished a king sized color falls quilt that I fmq'd on my Viking Sapphire. I w as breaking needles too, until I realized that I didn't have the quilt supported well enough on the table, and it was pulling just enough against the needle to let it hit the plate. Try making sure that all the weight is supported well on the table or on your shoulders.
Thread
Thread Starter
Forum
Replies
Last Post
Jamasue
Main
21
07-25-2015 05:10 PM
TeeGee
For Vintage & Antique Machine Enthusiasts
23
05-21-2012 09:03 AM