Chain piecing Woes...
02-04-2016, 05:06 AM
#21
Senior Member
Join Date: Mar 2011
Location: Durham, NC
Posts: 851
There's a difference between leaders and enders and a scrap piece (often called a spider) for starting and stopping. Leaders and enders are meant to become parts of another quilt. You basically have the pieces of a, say four patch for a secondary project at the ready. Then you start and stop your chain on those as you are working on chaining your main project parts together. Bonnie Hunter uses this method and this efficiency surely contributes to her amazing output.
I am not so organized. I like the idea but I'm usually too excited about what I'm doing to mess with being this organized. So I just grab a small scrap, fold it a time or two and it becomes my spider. I use three or four of these over and over, just snipping them off the chain for reuse. If you do this, you'll soon see why it's called a spider. I am sure I have pitched a thousand or more of these lifesaving "critters" into the trash over the years.
I am not so organized. I like the idea but I'm usually too excited about what I'm doing to mess with being this organized. So I just grab a small scrap, fold it a time or two and it becomes my spider. I use three or four of these over and over, just snipping them off the chain for reuse. If you do this, you'll soon see why it's called a spider. I am sure I have pitched a thousand or more of these lifesaving "critters" into the trash over the years.
Last edited by mhollifiel; 02-04-2016 at 05:12 AM. Reason: clarity - Lord knows it was needed!
02-04-2016, 05:43 AM
#22
Super Member
Join Date: Jun 2011
Location: Illinois
Posts: 9,018
so, from I gather, you construct each block completely, then on to the next one? Just wondering
02-04-2016, 05:50 AM
#23
Super Member
Join Date: Apr 2010
Location: Oregon
Posts: 3,418
I used to use a leader or "spider," as someone called it, but found that if I simply hold the thread tails snugly behind the machine, I never have to mess with another piece of fabric and snipping it off. If I had a scrap quilt planned, I might go back to the leaders and enders, however. But even starting a leader on a diagonal would mean holding those thread tails at the start. Each machine sews a little differently. I could get away with just beginning at the fabric edge with my old Kenmore.
02-04-2016, 06:25 AM
#24
Super Member
Join Date: Jan 2011
Location: Central FL
Posts: 1,478
I usually keep a piece of doubled fabric next to my sewing machine. I start sewing in the middle of this leader and then the first piece of my quilt chains together without any problems. I also hold onto both of my threads until the first few stitches are made.
02-04-2016, 06:37 AM
#25
Super Member
Join Date: Sep 2011
Location: Illinois
Posts: 5,621
I use leaders and enders as well but I noticed a new trend. I usually don't have this issue due to using leaders and enders but it started happening to me just the last few days. I realized I had a bobbin in with poor tension. When winding the bobbin, the thread had slipped out of one of the guides so the tension on the bobbin was not good, the thread wound on the bobbin was not nice and tight but spongy. I had wound the full bobbin and was loath to waste the thread so sewed a test strip with it. The tension was fine for sewing so I decided to use it and found I was getting the birds nest issue when chain piecing just as you describe. I am thinking it has something to do with my "spongy" wound bobbin. I am still to frugal (cheap!!) to give up on the bobbin and will continue to use it up but I am making sure I am putting some tension on my chain as I add each new unit. That is solving the issue for me. I am pretty sure once I use up this bobbin and load one that is wound correctly I will quit having the issue.
02-04-2016, 06:42 AM
#26
Power Poster
Join Date: Jul 2010
Location: SoCal
Posts: 12,232
A straight stitch plate, one small hole, can help significantly cut down on this problem. You can also use older machines that have but one small hole for the needle to go through. Now with all we expect the machines to do the openings in the plate are bigger. I bought a straight stitch plate with a small whole for my janome 6500. It was about $40 but it did cut down on the eating of fabric when piecing.
Last edited by Annaquilts; 02-04-2016 at 06:44 AM.
02-04-2016, 06:42 AM
#27
Super Member
Join Date: Sep 2011
Location: Illinois
Posts: 5,621
I kind of switch back and forth. Being a sewer first, I am still used to back stitching which isn't conducive to chain piecing, plus I often do applique or samplers and it doesn't work there either as each block is different. Recently when I did a huge churn dash quilt of 198 squares I had to remind myself to chain piece and it did speed up the process and I didn't get so bored with doing the same block over and over.
02-04-2016, 07:13 AM
#28
Super Member
Join Date: May 2012
Location: Central Wisconsin
Posts: 4,391
I thought it was the top thread which was most likely to become the "nest". If you use threads of a little different color, you will see which thread makes the nest.
02-04-2016, 08:36 AM
#29
Senior Member
Join Date: Oct 2010
Location: Moved from New Orleans to Port Neches, TX June 2014
Posts: 695
02-04-2016, 09:52 AM
#30
Power Poster
Join Date: Feb 2011
Location: Lowell, MA
Posts: 14,083
Besides using leaders, small bits of fabric that you stitch first, then stitch your pieces; I would also recommend what I have been told in the past, that you use a one hole face plate, as it helps keep the machine from "eating" fabric.
Thread
Thread Starter
Forum
Replies
Last Post
carslo
Pictures
28
10-25-2012 11:36 AM
