Go Back  Quiltingboard Forums > Main
Tablemats and birthing method >

Tablemats and birthing method

Tablemats and birthing method

Old 03-17-2015, 08:42 AM
  #1  
Junior Member
Thread Starter
 
Join Date: Apr 2014
Location: Essex, UK
Posts: 252
Default Tablemats and birthing method

I've just had my first go at making some tablemats using the birthing method. My problem is this: when I topstitch around the edge, the opening (through which the quilt has been birthed) always seems to get a little pucker in it, which I have been unable to avoid (I made 6 of them, and it happened on every one, to varying degrees). The pucker is always on the top, so it's quite noticeable. I used wonder clips to keep the opening tucked inside, perhaps pins would work better? Any hints or tips will be most appreciated!
Sisty88 is offline  
Old 03-17-2015, 09:11 AM
  #2  
Power Poster
 
Join Date: Dec 2010
Location: Michigan
Posts: 11,276
Default

Do you use an even feed/walking foot when you sew around your sandwich (before you birth it)? The top fabric may be slipping a bit. You could also experiment with the placement of the batting in the sandwich. You often are instructed to place it against the backing, but it will also work if you place it against the top. I would also pin for the first stitching, then use the clips for the top stitching.
PaperPrincess is offline  
Old 03-17-2015, 09:34 AM
  #3  
Super Member
 
Join Date: Mar 2011
Location: Pratt Kansas
Posts: 1,222
Default

If you are like me, you want the top to overhang a bit, so the back does not show on the front side.

When I layer my sandwich (before birthing), I pull the back a scootch tighter, about 3/16-1/4" shorter than the front, easing it all around the outer edges. When I birth, the back is smaller, and pulls to the back, thus disappearing.

This makes the front a tiny bit bigger, so you can get puckering in the birth opening. Try to have no ease at the opening, just on the sewn sections.

When you sew around the sandwich (before birthing), you want to make a 45 degree turn and sew off the edge of the seam allowance. (The colons represent your seam line to the outer edge of fabric.) I cant send a pic or a EQ drawing so try this:

-----------stitching line---------------: (Opening) :-------------------
________cut edge______________: (opening) :______________

When you turn it inside out, these sew-off-the-edge bits pull the seam allowance inside the placemat.

Also, if you use some kind of "batting", that helps keep the placemat from puckering. I use flannel. Gives the placemat another layer to protect the wood from the heat of the dishes, and a bit of absorption of liquids.
quiltmouse is offline  
Old 03-17-2015, 11:11 AM
  #4  
Junior Member
Thread Starter
 
Join Date: Apr 2014
Location: Essex, UK
Posts: 252
Default

Thank you for some fabulous advice! I really should have thought about the walking foot before, so I'll definitely try that next time (I have a bunch of other placemat tops ready to be made up!). As these ones are already done, I might just put some binding on them so that the pucker is covered up, as I want to try and sell them, and these are not up to scratch for that at the moment!
I think the order I did was batting, backing, top (from the bottom) and I did pin the sandwich, but not with very many pins, so maybe I need to pin it more thoroughly next time!
I like the sound of the 45 degree sewing off the edge to help with turning under! I definitely found that part the hardest, so I think that will really help!
Sisty88 is offline  
Old 03-17-2015, 01:25 PM
  #5  
Super Member
 
Join Date: Nov 2011
Location: Tn
Posts: 8,643
Default

Can you piece the backing? If so, you can leave an opening in the back seam to turn thru. This way you can stitch all the way around your piece and hand stitch the opening on the back where it will not show.
cjsews is offline  
Old 03-17-2015, 01:33 PM
  #6  
Junior Member
 
Join Date: Jan 2010
Location: colorado
Posts: 231
Default

Before I sew around I use fusible web and fuse the opening closed. I use the lightweight sewable fusible. I then don't have to worry about things moving around on me and I don't have to pin the opening closed.
quilterjody is offline  
Old 03-17-2015, 03:46 PM
  #7  
Member
 
Join Date: Nov 2011
Posts: 73
Default

Method I learned. Sew the seam shut & if you have a border untsitch that. & turn. did 3 sets & they looked nice. I can never get the seam closed nicely until I did this method. sorry I don't do pics. & don't remember where i got the idea. Maybe a quiltmaker mag with a quilt.
Leonita is offline  
Old 03-17-2015, 03:55 PM
  #8  
Senior Member
 
Join Date: Nov 2011
Location: Cary, NC
Posts: 383
Default

Do you have any Wonder Tape? It's a narrow, double-sided, sticky tape that washes out. Since it's sticky on both sides, the cloth doesn't have a chance of moving.

I bought it for sewing zippers and now I use it for lots of things.

Tate
tate_elliott is offline  
Old 03-17-2015, 04:29 PM
  #9  
Super Member
 
PenniF's Avatar
 
Join Date: Jun 2012
Location: North Texas formerly The Burgh
Posts: 3,392
Default

Even with a walking foot i used to have trouble with that uneven-ness....Elmer's school glue to close it up before sewing solved the problem for me. Oh....and i also always leave a little extra seam allowance in that area.
PenniF is offline  
Old 03-17-2015, 05:16 PM
  #10  
Senior Member
 
Join Date: Feb 2015
Posts: 637
Default

Thanks for posting this thread.

Some great ideas right on time!

(I'm making placemats for my mom)
DresiArnaz is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Thinkuvme2
Links and Resources
11
05-07-2012 06:43 PM
taiboo
Main
25
07-06-2011 09:01 PM
Magoo
Main
5
06-24-2011 01:29 PM
k3n
Pictures
51
11-07-2010 12:06 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter