Did I ruin my machine?

Old 01-24-2013, 08:23 PM
  #1  
Member
Thread Starter
 
Join Date: Feb 2011
Location: Michigan
Posts: 54
Default Did I ruin my machine?

Today, knowing that I was going to try out the ruffler and practice for a Christening gown I'm working on, I oiled my Singer 301. So, I'm looking at the instructions, take off the bottom, drip oil all over, take off the top, look at all the arrows, and when I'm done I take a closer look at the written instructions.

Do not ever oil the gears. Oops. I oiled the gears. You are supposed to use "lubricant", which apparently is a different species from oil.

I did set up the ruffler and try it out. What do I do?
Maura is offline  
Old 01-24-2013, 08:37 PM
  #2  
Super Member
 
Gladys's Avatar
 
Join Date: Jan 2011
Location: North Carolina
Posts: 3,372
Default

Oh my, bless your heart. I can't wait for you to get an answer cause I'm sure I would have done the same thing eventually.
Gladys is offline  
Old 01-24-2013, 09:01 PM
  #3  
Power Poster
 
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 41,445
Default

The lubricant that goes onto the gears on my machine is a thicker kind of goopy stuff. Machine oil will probably disolve the lubricant if there was some on the gears. I don't think it will do any damage but the gears will have to be re-lubricated to prevent wear on the gears? I am not a machine expert so I am just guessing.
Tartan is offline  
Old 01-24-2013, 10:44 PM
  #4  
Junior Member
 
Join Date: Sep 2012
Posts: 134
Default

i'm not an expert either, but if i were you, i would try to wipe the oil off of the gears (turn them by hand and gently clean off what you can with something that won't leave lint behind) then add lubricant to the gears.
oregongirl is offline  
Old 01-24-2013, 11:21 PM
  #5  
sap
Junior Member
 
Join Date: Dec 2010
Location: mid MI
Posts: 288
Default

both of above answers are correct. I rehabilitate SM and use oil to often the gunk under the hood around the gears. when I'm finished I put more axle grease on the gears. (men have their toys, so do I.)
sap is offline  
Old 01-24-2013, 11:30 PM
  #6  
Super Member
 
ArchaicArcane's Avatar
 
Join Date: Jul 2012
Location: Not Here
Posts: 3,817
Default

Singer lube is getting harder to find. Jenny has it at Sew Classic, and most shops should be able to order it, but you may have to buy 6 tubes at a time (minimum order for most dealers, here in Canada at least, so YMMV)

This is what Singer recommends for the gears. It's thicker, stays in place, and doesn't "liquify" as fast when it gets warm, hence why we also use it in the Singer motors that require it.

That said, I've heard of people using all sorts of grease on the gears (the motor must have the Singer lube, so it doesn't hurt to buy it and use it for the gears too) - TriFlow's grease product, Vaseline, axle grease, etc.

And no, you didn't ruin your machine. You just aren't finished the maintenance.
ArchaicArcane is offline  
Old 01-24-2013, 11:38 PM
  #7  
Junior Member
 
Join Date: Sep 2012
Posts: 134
Default

i was just reading on a site of a person's experience with the mess Vaseline can make in machines because it melts and puddles. i think i'd stick with the lubricant.
oregongirl is offline  
Old 01-24-2013, 11:54 PM
  #8  
Super Member
 
ArchaicArcane's Avatar
 
Join Date: Jul 2012
Location: Not Here
Posts: 3,817
Default

I don't think I'd ever use it personally. I've heard of it, but I don't think I've ever had a "Grease emergency" where I'd need something that quickly. There are so many good greases out there for gears that there's not a lot of reason for it.

I wouldn't mind seeing the site you mentioned...?
ArchaicArcane is offline  
Old 01-25-2013, 02:23 AM
  #9  
Super Member
 
Join Date: Feb 2012
Posts: 8,091
Default

Go to Sew-Classic and buy a tube of TRI-FLOW grease and oil. Lube the gears with the grease and everything else with the oil. The T-F grease is superior to the Singer Lube for gears and works wonders on them. You should also pick up a couple tubes of the Singer Lube for the motors that use it too.

You didn't hurt the machine but the oil you put on the gears will not lube them for long.

Joe
J Miller is offline  
Old 01-25-2013, 09:06 AM
  #10  
Junior Member
 
quiltgal's Avatar
 
Join Date: Apr 2011
Location: Texas
Posts: 246
Default

Originally Posted by Maura View Post
Today, knowing that I was going to try out the ruffler and practice for a Christening gown I'm working on, I oiled my Singer 301. So, I'm looking at the instructions, take off the bottom, drip oil all over, take off the top, look at all the arrows, and when I'm done I take a closer look at the written instructions.

Do not ever oil the gears. Oops. I oiled the gears. You are supposed to use "lubricant", which apparently is a different species from oil.

I did set up the ruffler and try it out. What do I do?
I agree with the replies. It will drip, but will clean up. Then get some lube and put on the gears. I have supplies at my website if you can not find locally: www.thequiltgal.com. Singer lubricant is the same for all the Singer machines, Featherweight 221s etc that require lubricant.
quiltgal is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
runninL8
For Vintage & Antique Machine Enthusiasts
25
10-24-2013 06:09 AM
Liz aka Helen
Main
106
05-14-2011 04:33 PM
Liz aka Helen
Main
157
05-01-2011 12:59 PM
Liz aka Helen
Main
38
04-19-2011 01:56 PM
trupeach1
General Chit-Chat (non-quilting talk)
26
07-09-2010 05:27 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter