Go Back  Quiltingboard Forums > Main > For Vintage & Antique Machine Enthusiasts
Old Sewing Machine Identification >

Old Sewing Machine Identification

Old Sewing Machine Identification

Old 10-03-2018, 03:53 PM
  #31  
Member
Thread Starter
 
Join Date: Sep 2018
Posts: 21
Default

I picked up some pb blaster today and gave it a try. Just pb blaster alone didn't do much. Maybe if I waited long it would have. With the help of the torch I got s couple more screws loose. Just a word of caution. If you heat up metal and spray pb blaster on it, you will see a lot of smoke and I mean a lot. Its a good thing that I was working with the door open in the shop.
Yes patience is key. This is not my first rodeo with trying to loosen extremely rusted parts. I know it probably won't happen but it would sure be nice if it would unseize over night.
Massey850 is offline  
Old 10-03-2018, 06:54 PM
  #32  
Member
 
Join Date: Aug 2018
Posts: 23
Default

I like Kroil best, and time will help any penetrating oil. Days or weeks. You might try dropping the whole machine in a bucket of diesel and let it soak. Ironically, boiling can also remove rust. You'd need a big pot, and you can't borrow my brew kettle for that.
John Sand is offline  
Old 10-04-2018, 09:28 AM
  #33  
Super Member
 
Join Date: Sep 2015
Posts: 1,963
Default

The annyoing thing about Kroil and PB Blaster is much the same as WD-40, the active ingredients are secret, listed under a % of proprietary agents. There is more than a bit of wild goose chase involved when going for one or the other, or just trying different stuff. There are brands that make different blends and let us know what the active ingredient is, like CRC. Applying the right stuff and let it go to work is probably the only way in cases like this, let it stand for a week or three, then reapply or altering with something else.
Mickey2 is offline  
Old 10-09-2018, 05:08 PM
  #34  
Member
Thread Starter
 
Join Date: Sep 2018
Posts: 21
Default

Well, I think I figured out the mystery to getting these screws and parts unseized. What I did today was heated up some screws to red hot. I waited a second for them to turn dark again and tried turning so I turned them a bit. Then I sprayed some pb blaster and they turned out like a dream.
Massey850 is offline  
Old 10-09-2018, 05:48 PM
  #35  
Super Member
 
OurWorkbench's Avatar
 
Join Date: Mar 2015
Location: Denver, CO
Posts: 4,222
Default

Great! Thank you for letting us know what worked and evidently well.


Janey - Neat people never make the exciting discoveries I do.
OurWorkbench is offline  
Old 10-10-2018, 06:30 AM
  #36  
Super Member
 
leonf's Avatar
 
Join Date: May 2016
Location: near Topeka kansas
Posts: 4,524
Default

impressive. I've used hair dryer heat, but not a torch. Yet.
leonf is offline  
Old 10-10-2018, 07:29 PM
  #37  
Member
Thread Starter
 
Join Date: Sep 2018
Posts: 21
Default

I've never heard of using a hair dryer for heating up parts. For my machine, I need a torch. If I had an oxy acetylene torch, it would be even better because its a smaller flame thats hotter. I could get parts to red hot in just a few seconds but the propane torch is doing its job alright. These parts are so rusted in place but slowly I'm getting them out.
Massey850 is offline  
Old 10-11-2018, 06:06 AM
  #38  
Super Member
 
leonf's Avatar
 
Join Date: May 2016
Location: near Topeka kansas
Posts: 4,524
Default

Hair dryer is for simpler repairs. Melting old stuck grease and such. I've used a torch on old tractors with stuck parts. Never considered it on a sewing machine.
leonf is offline  
Old 10-24-2018, 03:34 PM
  #39  
Member
Thread Starter
 
Join Date: Sep 2018
Posts: 21
Default

Well, Its been a while and I have an update. Not on the machine, its still coming apart piece by piece. This is something related to this sewing machine. I somehow found the table for this machine at my place, well, whats left of it. I haven't found it all yet I'm go this weekend and see what I can find for parts. I'll take pictures too. It was in the most interesting place. It was under some old heavy steel wheel off of a piece of farm equipment that was nowhere near where I found the sewing machine.
Massey850 is offline  
Old 10-24-2018, 03:57 PM
  #40  
Super Member
 
leonf's Avatar
 
Join Date: May 2016
Location: near Topeka kansas
Posts: 4,524
Default

glad you found it. every bit is history.
leonf is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Mesha
For Vintage & Antique Machine Enthusiasts
12
09-02-2020 05:59 PM
Glowygirl2
For Vintage & Antique Machine Enthusiasts
1
10-27-2018 06:10 AM
stargatesg1sean
For Vintage & Antique Machine Enthusiasts
14
07-23-2015 06:45 AM
ElizabethT
Main
30
08-15-2014 06:56 PM
stitchinwitch
Main
14
02-15-2011 01:38 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter