Questions about a newly acquired Singer 401A missing parts
09-05-2011, 05:57 PM
#22
Super Member
Join Date: Feb 2011
Location: Webster, NY
Posts: 1,002
Originally Posted by miriam
To wind the bobbin you put a spool on the pin at the bottom right corner. Run that thread through the little thing next to it and up - there is a thing with a wheel - on the opposite side of the wheel is a spindle you can put the bobbin on it, run that thread through and push the rubber wheel against the balance wheel and you are good to wind the bobbin. You can release the clutch so the needle won't move. Just give the knob inside the balance wheel a turn and you are good to go. When you are done you can just put the wheel back where it was and the needle will go again. You can make the next bobbin while you are sewing. Just keep the balance wheel engaged as you wind it. I had no manual when I got the one out of the trash. It took a while for me to figure out all the stitch patterns. Be sure to read that part carefully in the manual.
09-05-2011, 06:04 PM
#23
Power Poster
Join Date: Mar 2011
Location: Somewhere
Posts: 15,507
Originally Posted by deplaylady
Originally Posted by miriam
To wind the bobbin you put a spool on the pin at the bottom right corner. Run that thread through the little thing next to it and up - there is a thing with a wheel - on the opposite side of the wheel is a spindle you can put the bobbin on it, run that thread through and push the rubber wheel against the balance wheel and you are good to wind the bobbin. You can release the clutch so the needle won't move. Just give the knob inside the balance wheel a turn and you are good to go. When you are done you can just put the wheel back where it was and the needle will go again. You can make the next bobbin while you are sewing. Just keep the balance wheel engaged as you wind it. I had no manual when I got the one out of the trash. It took a while for me to figure out all the stitch patterns. Be sure to read that part carefully in the manual.
09-05-2011, 06:53 PM
#24
Super Member
Join Date: Feb 2011
Location: Webster, NY
Posts: 1,002
Originally Posted by miriam
Originally Posted by deplaylady
Originally Posted by miriam
To wind the bobbin you put a spool on the pin at the bottom right corner. Run that thread through the little thing next to it and up - there is a thing with a wheel - on the opposite side of the wheel is a spindle you can put the bobbin on it, run that thread through and push the rubber wheel against the balance wheel and you are good to wind the bobbin. You can release the clutch so the needle won't move. Just give the knob inside the balance wheel a turn and you are good to go. When you are done you can just put the wheel back where it was and the needle will go again. You can make the next bobbin while you are sewing. Just keep the balance wheel engaged as you wind it. I had no manual when I got the one out of the trash. It took a while for me to figure out all the stitch patterns. Be sure to read that part carefully in the manual.
09-05-2011, 07:07 PM
#25
Power Poster
Join Date: Mar 2011
Location: Somewhere
Posts: 15,507
I would never have thought of winding the bobbins as I sew but the industrial machines do it. It is really nice though. You don't have to take time out. I love the 401 - you just slide it open and you can peek to see how much thread is left in there.
09-06-2011, 09:02 AM
#27
Power Poster
Join Date: Mar 2011
Location: Somewhere
Posts: 15,507
Originally Posted by kayahr
My Mom's 401-A has additional cams. She still uses the machine. Love the fact that it cam with a quarter-inch foot. I thought about buying a walking foot for it.
Thread
Thread Starter
Forum
Replies
Last Post
AnInspiredMess
For Vintage & Antique Machine Enthusiasts
7
03-31-2019 11:14 AM
dwhitesmith
For Vintage & Antique Machine Enthusiasts
15
02-18-2016 09:29 AM
Friday1961
For Vintage & Antique Machine Enthusiasts
15
03-14-2015 06:28 PM
jennb
For Vintage & Antique Machine Enthusiasts
6
06-16-2012 04:38 PM
