Help with design wall
#1
Senior Member
Thread Starter
Join Date: Dec 2008
Location: central California
Posts: 636
I have read all the recent posts about design walls. I have looked all over for the pink or blue insulation foam boards that have been recommended here. Neither our Home Depot nor Lowes have them, all they had was the white styrefoam, so that is what I got. I bought fleece to wrap around it. I bought a spray glue, but when I got home I read the very small hard to find, small print and it said not to use on styrefoam. I decided to just use duct tape on the back. It seemed to be fine, for a few days, now the fleece is pulling away from the tape. My DH didn't think staples would hold in styrefoam. I would be so thankful for any ideas from all of you.
#3
If you check with Lowes, there may be a spray glue that will work. Just spray on the back side of the foam and glue down the fleece there. I wouldn't use it on the front incase any glue leeches through...
#4
Senior Member
Thread Starter
Join Date: Dec 2008
Location: central California
Posts: 636
Originally Posted by sharon b
Can you locate the longer pins that look like a T they are hobby pins and should hold the fabric in and down .
How thick is the foam ?
How thick is the foam ?
#6
I think that part of the problem is that the fleece is too heavy. I'd purchase a thin, cheap flannel in white or another light color. I assume that you've purchased a 4 x 8 sheet of styrofoam, so a 44 inch flannel fabric won't go around the edges to the back. If that's the case, you can stitch a narrow piece of fabric to the edges. But I wouldn't make myself crazy about that. Instead, I'd make some "straps" out of elastic. You sew the elastic on one edge about 8 or 10 inches from the corner, then go around the back of the board diagonally to the adjacent edge. Sew elastic so that all four corners can be attached. This may be enough but I would consider adding elastic on the long side that goes around the back to the opposite long side. This will hold the center section in place. When all five pieces of elastic are stitched on, you slide the center elastic on, then attach the corner pieces in place. The elastic will stretch to make it easy to put on and then go back into shape to hold the flannel.
#7
Senior Member
Thread Starter
Join Date: Dec 2008
Location: central California
Posts: 636
Originally Posted by fleurdelisquilts.com
I think that part of the problem is that the fleece is too heavy. I'd purchase a thin, cheap flannel in white or another light color. I assume that you've purchased a 4 x 8 sheet of styrofoam, so a 44 inch flannel fabric won't go around the edges to the back. If that's the case, you can stitch a narrow piece of fabric to the edges. But I wouldn't make myself crazy about that. Instead, I'd make some "straps" out of elastic. You sew the elastic on one edge about 8 or 10 inches from the corner, then go around the back of the board diagonally to the adjacent edge. Sew elastic so that all four corners can be attached. This may be enough but I would consider adding elastic on the long side that goes around the back to the opposite long side. This will hold the center section in place. When all five pieces of elastic are stitched on, you slide the center elastic on, then attach the corner pieces in place. The elastic will stretch to make it easy to put on and then go back into shape to hold the flannel.
#8
Super Member
Join Date: Aug 2007
Location: s.cal
Posts: 2,039
why don,t you make a cover like a pillow case to keep the board from dust or coming apart from corners ,i think this will give it more protection and support from pulling in and out from behind headboard when you,er not using it
#9
Super Member
Join Date: Feb 2010
Location: Maryland
Posts: 3,586
Originally Posted by fleurdelisquilts.com
I think that part of the problem is that the fleece is too heavy. I'd purchase a thin, cheap flannel in white or another light color. I assume that you've purchased a 4 x 8 sheet of styrofoam, so a 44 inch flannel fabric won't go around the edges to the back. If that's the case, you can stitch a narrow piece of fabric to the edges. But I wouldn't make myself crazy about that. Instead, I'd make some "straps" out of elastic. You sew the elastic on one edge about 8 or 10 inches from the corner, then go around the back of the board diagonally to the adjacent edge. Sew elastic so that all four corners can be attached. This may be enough but I would consider adding elastic on the long side that goes around the back to the opposite long side. This will hold the center section in place. When all five pieces of elastic are stitched on, you slide the center elastic on, then attach the corner pieces in place. The elastic will stretch to make it easy to put on and then go back into shape to hold the flannel.
#10
I think I've seen a design wall made with hinges between the sheets
of insulation so you can fold it when not in use. I guess you'd have
to frame it first then attach the hinges to the frame.
Making one right now but mine will be attached to the wall.
By the way, we are using construction adhesive 2000 made just for styrofoam.
of insulation so you can fold it when not in use. I guess you'd have
to frame it first then attach the hinges to the frame.
Making one right now but mine will be attached to the wall.
By the way, we are using construction adhesive 2000 made just for styrofoam.
Thread
Thread Starter
Forum
Replies
Last Post
Chester the bunny
Main
10
10-28-2011 03:13 PM
craftybear
Links and Resources
6
08-22-2011 05:12 PM
craftybear
Main
35
05-20-2011 01:45 PM
craftybear
Links and Resources
5
05-18-2011 07:04 AM