How to start/stop with machine quilting...
#1
Senior Member
Thread Starter
Join Date: Jun 2010
Location: South Range, WI
Posts: 458
How to start/stop with machine quilting...
This is probably a dumb question, but it seems that when I try to quilt a top on my domestic machine, the back always looks messy where I start and stop the stitching. If I use the tacking mechanism, it is too obvious, but it seems important to tie off those ends. Is there a method anyone can suggest to make the starts/stops less noticeable? I try to use a matching or neutral bobbin thread when possible. I appreciate any advice you can give me.
#2
Super Member
Join Date: Oct 2010
Location: Nebraska
Posts: 3,255
Some people recommend ending your stitching by making a few tiny stitches in place, then trim off the ends. Another method which I usually use is to just trim off ends fairly long and then go back and using a needle, pull them to the inside of the quilt. It is not noticeable that way. The method I use is better described on LeahDay.com. She has lots of information on her site related to free motion quilting and recently, walking foot quilting.
#3
Power Poster
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 41,535
I always leave thread tails so I can bring them to one side, knot them and bury the ends in the quilt sandwich with an easy thread needle. Yes, it is a tedious job but I have no detectable stops when I am done.
#4
Super Member
Join Date: May 2012
Location: S.E. Queensland, Australia
Posts: 1,487
I pull the (long) threads up to the top with the first stitch, & holding firmly, sew 2 stitches in reverse and a few more forward, which holds the reverse stitches securely, then trim. Have had no problems with that.
#5
Power Poster
Join Date: Mar 2009
Posts: 15,639
I pull the bobbin thread to the top and make tiny starting stitches. When done, I make tiny stitches, then pull the bobbin thread to the top and trim. Recently I worked with thick thread and I still pulled the bobbin thread up but I left a long tail of each and sewed them in with a needle.
#6
Senior Member
Thread Starter
Join Date: Jun 2010
Location: South Range, WI
Posts: 458
Thank you ladies! I seem to have difficulty pulling that bobbin thread up - or at least it seems tedious to me, so I may try Tartan's method of leaving the long tails and going back to pull them to one side. I appreciate the help....it is always good to know there is advice available here on the board.
#8
Super Member
Join Date: Aug 2010
Posts: 2,237
This is what I usually do, too, especially on a quilt I know will be washed a lot (for a child, a person in the hospital, etc.)
#9
Super Member
Join Date: Sep 2010
Location: Heart of Colorado's majestic mountains!
Posts: 6,026
I also pull the bobbin thread to the top, hold it in place and stitch two stitches in place and move forward. I try to have as many starts and stops in the edges so the binding covers them. However, in the middle of the quilt starts and stops I will tie and bury into the quilt sandwich. It is unfortunate to spoil the look of a finished quilt by being careless when you are nearly finished.
#10
Super Member
Join Date: Oct 2015
Location: Va.
Posts: 5,753
Depending on what the quilt is for I will use just about any of the methods mentioned above. The only one I don't use is leaving the bobbin tail long on the back since I tend to have problems with thread nests when I do that.
If the quilt will will be used and subjected to lots of washing I do a combination of tiny stitches and backtracking to start and stop.
If it is an art piece that will be mounted on a stretcher or panel so the back is completely hidden then I tend to use my machine's thread cutter button which pulls the threads to the back, knots them and trims them short.
If it's a wall piece that will be hung using a sleeve, or hung using some other method that leaves the back exposed, then I bring both threads to the front, knot them and then bury them. I do this as I go-- it doesn't slow me down all that much since I also use that pause to decide where I'm going next.
Rob
If the quilt will will be used and subjected to lots of washing I do a combination of tiny stitches and backtracking to start and stop.
If it is an art piece that will be mounted on a stretcher or panel so the back is completely hidden then I tend to use my machine's thread cutter button which pulls the threads to the back, knots them and trims them short.
If it's a wall piece that will be hung using a sleeve, or hung using some other method that leaves the back exposed, then I bring both threads to the front, knot them and then bury them. I do this as I go-- it doesn't slow me down all that much since I also use that pause to decide where I'm going next.
Rob
Thread
Thread Starter
Forum
Replies
Last Post
nanna-up-north
For Vintage & Antique Machine Enthusiasts
13
10-28-2013 12:53 PM
lisalisa
General Chit-Chat (non-quilting talk)
54
02-19-2011 11:01 AM