Go Back  Quiltingboard Forums >
  • Main
  • Inexpensive Sewing Table - Instructions and Photos >
  • Inexpensive Sewing Table - Instructions and Photos

  • Inexpensive Sewing Table - Instructions and Photos

    Thread Tools
     
    Old 10-27-2011, 06:47 AM
      #1  
    Member
    Thread Starter
     
    purvissp's Avatar
     
    Join Date: Mar 2011
    Location: Newark, DE
    Posts: 35
    Default

    I have checked out the various lines of sewing cabinets and cutting tables and I thought they were rather expensive.

    So I designed and started building some very inexpensive sewing cabinets and work tables. They may not look as fancy as those in the stores, but they are much cheaper and just as functional.

    Sorry if this is long, but I tried to include all the instructions for building these tables. Hope it helps some of you.

    You can also build work/cutting table using this process, just get larger pieces of MDF for the tops and shelves.

    It is much nicer sewing with your machine sunken into a flat table top.

    Below are a few photos that may give you some ideas and if you or your spouse is at all handy with woodworking tools you may want to try building some of these.

    The 3 main materials I use are:

    ½” MDF board for the tops – for the smaller tables I buy the 2’x4’ precut pieces at Home Depot for $8.96.
    2”x2” lumber for the legs. I actually use 2”x4” and rip to 2”x2” on a table saw.
    1”x5” or 1”x6” for the sides and center support for the machine.

    You can make the tables as long as you like, up to 48”. I usually make mine 40”.

    To make the top make a template to outline the contour of your machine to cut an opening in the MDF board that will fit your machine. If your machine has a plastic extension table that is a good start for a template. I found I have to extend the cutout in the MDF about 6” larger than the machine (on the right side of the opening). This allows you to set the machine in the opening and then slide it to the left to fit the contoured opening.
    You will also need to either rout or sand the edges to a smooth rounded shape, primarily on the left front, side and back, where you want the fabric to slide easily.

    I also put 2 coats of clear shellac on the surface of the MDF to make if slicker for the fabric to slide.

    I then start on the frame. I first cut 4 2”x2” boards for the legs 29” long. You can sand them it you would like to smooth them up to stain and varnish.

    I then cut the 1”x5” or 1”x6” boards for the side rails. Be sure to allow for some overhang of the top. I always allow a 1” overhang on all sides.
    And also consider the 1 ½’ legs on each end of the sides.

    Example: Top is 24”x 40”, then front side rail = 40”- 2” overhang(each end) – 3” (for 2 legs) = cut front and back rails to 35”. Side rails = 24” – 2” – 3” = cut side rails to 19”

    Now assemble the frame. Mount legs to rails. Various methods, pocket screws, drill legs and use long drywall screws, buy corner brackets and screw together. Whichever is easiest for you. I also glue the ends of the rails to the legs.

    Next step is to screw a 1”x 6” board across the bottom, running from the left end rail to the right end rail. This is to support the sewing machine in the table. To locate the place to install the bottom support, temporarily place the MDF top on the table were it will be permanently mounted. Mark and mount the bottom support 1” x 6” directly below the opening in the top MDF board.

    Once the lower support is mounted you can install (screw) the MDF top to the frame. Note you will most likely have to use 1 or 2 small pieces of 1/4” plywood to raise the machine to the proper height to be flush with the top.
    Attached Thumbnails Click image for larger version

Name:	Attachment-277755.jpe
Views:	3328
Size:	48.5 KB
ID:	277808   Click image for larger version

Name:	Attachment-277756.jpe
Views:	3352
Size:	42.7 KB
ID:	277809   Click image for larger version

Name:	Attachment-277757.jpe
Views:	3309
Size:	45.0 KB
ID:	277810  
    purvissp is offline  
    Old 10-27-2011, 06:49 AM
      #2  
    Member
    Thread Starter
     
    purvissp's Avatar
     
    Join Date: Mar 2011
    Location: Newark, DE
    Posts: 35
    Default

    Also, here is a 38"x38" cutting/work table built with the same process.
    Attached Thumbnails Click image for larger version

Name:	Attachment-277758.jpe
Views:	3331
Size:	57.4 KB
ID:	277811  
    purvissp is offline  
    Old 10-27-2011, 06:50 AM
      #3  
    Super Member
     
    sewwhat85's Avatar
     
    Join Date: Nov 2010
    Location: missouri
    Posts: 6,311
    Default

    nice table
    sewwhat85 is offline  
    Old 10-27-2011, 06:56 AM
      #4  
    Senior Member
     
    Join Date: Dec 2010
    Location: Kentucky
    Posts: 361
    Default

    Wow, very professional looking!
    pipp5 is offline  
    Old 10-27-2011, 06:57 AM
      #5  
    Super Member
     
    marilynr's Avatar
     
    Join Date: Sep 2010
    Location: Oregon
    Posts: 1,604
    Default

    Great job.
    marilynr is offline  
    Old 10-27-2011, 07:02 AM
      #6  
    Senior Member
     
    Join Date: Feb 2010
    Location: Ft. Myers, Florida
    Posts: 928
    Default

    It looks very professional to me, I wish I lived close enough for you to make one for me :) :)
    Terryl is offline  
    Old 10-27-2011, 07:02 AM
      #7  
    Super Member
     
    Join Date: Aug 2007
    Location: Clay Springs AZ
    Posts: 3,229
    Default

    Very nice job.
    Rose Marie is offline  
    Old 10-27-2011, 07:05 AM
      #8  
    Senior Member
     
    debs's Avatar
     
    Join Date: Oct 2009
    Location: Riesel, TX ( HOT )
    Posts: 517
    Default

    Very nice and many thanks for the directions!

    Now to find the time!

    Debs
    debs is offline  
    Old 10-27-2011, 07:09 AM
      #9  
    Super Member
     
    fayzer's Avatar
     
    Join Date: Sep 2010
    Location: Destin, Fl
    Posts: 1,878
    Default

    Beautiful work. Too bad that I can't do this. I don't do table saws. I'd probably cut off my fingers.
    fayzer is offline  
    Old 10-27-2011, 07:44 AM
      #10  
    Super Member
     
    Join Date: Apr 2007
    Location: North Carolina - But otherwise, NOTW
    Posts: 7,940
    Default

    Brilliant!!! Thanks for the tutorial!!
    jljack is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    bvillequilter
    Pictures
    20
    10-27-2021 09:26 AM
    JoyceHoopes
    Main
    7
    11-30-2013 03:09 PM
    Sneed
    Main
    8
    08-25-2013 07:50 PM
    BellaBoo
    Links and Resources
    20
    10-07-2012 11:34 AM
    purvissp
    Pictures
    102
    04-06-2011 01:53 AM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is On
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter