Go Back  Quiltingboard Forums >
  • Main
  • I need some advice >
  • I need some advice

  • I need some advice

    Thread Tools
     
    Old 12-30-2011, 05:36 AM
      #1  
    Member
    Thread Starter
     
    Join Date: Sep 2011
    Location: Redding CA
    Posts: 15
    Default I need some advice

    Hi all-I am hoping for a miracle I think. I am doing a scrappy quilt. All was going "okay" until I began adding the borders and this quilt has taken on a life of it's own. The inside of the quilt is stretching every which way the more I am handling it. Is there anyway to calm this thing down? I am afraid by the time I finish it is going to all wonky. I did use "Best Press" while pressing but no steam. (But I guess that acts as steam?)
    Lotsapies is offline  
    Old 12-30-2011, 07:11 AM
      #2  
    Super Member
     
    jitkaau's Avatar
     
    Join Date: Aug 2010
    Location: Australia
    Posts: 4,116
    Default

    It sounds like you are playing with bias edges too much. Best to try not to cut too many bias edges which are joined to other biases. Don't iron and press all of the time if you notice your quilt is growing. Just gently finger press. If it becomes a real problem, you might find that doing some 'stay stitching' around each shape might be the best solution. It will be tedious but is an age old dressmaking trick for bias edges. Hope you have better success with it.
    jitkaau is offline  
    Old 12-30-2011, 07:15 AM
      #3  
    Super Member
     
    Scissor Queen's Avatar
     
    Join Date: Jul 2009
    Location: Southwest Kansas
    Posts: 4,820
    Default

    When you sew the border on sew with the quilt top next to the feed dogs. The rule is "bias on the bottom." It really helps control any stretch.
    Scissor Queen is offline  
    Old 12-30-2011, 07:15 AM
      #4  
    Senior Member
     
    fatquarters's Avatar
     
    Join Date: Sep 2010
    Posts: 833
    Default

    So are you saying that the edges stretched when attaching boarders, and that made iT wonky?
    fatquarters is offline  
    Old 12-30-2011, 07:20 AM
      #5  
    Super Member
     
    Join Date: Sep 2010
    Location: Keller, TX
    Posts: 7,417
    Default

    When you sew on the borders, you should sew from the middle out. More work but helps control the stretching.
    lfstamper is offline  
    Old 12-30-2011, 07:26 AM
      #6  
    Power Poster
     
    dunster's Avatar
     
    Join Date: Mar 2009
    Location: Lake Elsinore, CA
    Posts: 15,163
    Default

    Maybe if you show a picture it would be easier to diagnose what is happening. It could be bias edges, or cups in the piecing, or borders not cut correctly (although that would probably mean the borders were waving, not the inside of the quilt). You might be able to carefully block the quilt to get it flat and straight.
    dunster is offline  
    Old 12-30-2011, 07:56 AM
      #7  
    Power Poster
     
    Join Date: Mar 2011
    Location: Ontario, Canada
    Posts: 41,481
    Default

    If I am understanding the problem, than the many different bias pieces are causing the quilt to stretch as you sew the borders on? I don't see any way to avoid it except applying some kind of fusible to the back of the whole quilt (pricey). I think I would go ahead and quilt it without borders. I would then re-square the quilt and add my borders Quilt as You Go style. The quilting will stabilize the quilt and then you can add the borders.
    QAYG- You lay the border right side down on the quilt (pin). You lay the backing piece right side down to the back(pin). You put a strip of batting pinned to either the front or back piece and sew the pinned sections on the top edge of the quilt.You press all of them outwards and then do the same to the bottom of the quilt. You then repeat the process on the sides and then finish quilting the borders and bind. Good Luck!
    Tartan is offline  
    Old 12-30-2011, 07:59 AM
      #8  
    Senior Member
     
    Join Date: Apr 2011
    Location: Texas
    Posts: 429
    Default

    My suggestion is stay-stitching all around the edge before putting your borders on. Kind of helps hold everything in place.
    LindaDeeter is offline  
    Old 12-30-2011, 08:06 AM
      #9  
    Super Member
     
    Join Date: Oct 2010
    Location: IN
    Posts: 1,153
    Default

    I think I'd go with the stay stitching. In the future, be careful when pressing the bias edges. Too heavy a hand or moving the iron (ironing vs pressing) will definitely cause distortion. Good luck, I hope it turns out beautifully for you!
    Val in IN is offline  
    Old 12-30-2011, 08:29 AM
      #10  
    Member
    Thread Starter
     
    Join Date: Sep 2011
    Location: Redding CA
    Posts: 15
    Default

    I knew I could count on you guys-thanks for all the great advice. Lessons learned here for next time for sure! Happy New Year!
    Lotsapies is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    greaterexp
    Main
    30
    08-07-2015 09:05 PM
    GMA
    Pictures
    9
    10-11-2012 05:01 AM
    Homespun
    Pictures
    79
    08-23-2011 11:18 AM
    Rainforest_elf
    Main
    6
    12-04-2008 03:58 PM
    Diamonds
    Main
    5
    01-10-2008 08:58 AM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is On
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter