Got any Tool Tips?
#51
"Ron you are sssssssssssoooooooooooooooo far over my head."
Miriam, not really. I'm trying to accomplish the same as you are with the dimmer switch for your Dremel. I'm using the inline foot control as a "dimmer" switch. I can set it at 6 different levels. If I set it at the lowest level it will allow the "down stream" foot control to only reach a maximum of very slow. The next level of the inline will allow a little more maximum speed of the "down stream" control. And so on up to the six level not affecting the "down stream" controller whatsoever.
The purpose is to limit the maximum speed of my sewing. I am not expert at controlling speed. This allows me to control the maximum speed and gives more graduated increments of speed. Same as your dimmer switch regulating the speed of your Dremel.
Miriam, not really. I'm trying to accomplish the same as you are with the dimmer switch for your Dremel. I'm using the inline foot control as a "dimmer" switch. I can set it at 6 different levels. If I set it at the lowest level it will allow the "down stream" foot control to only reach a maximum of very slow. The next level of the inline will allow a little more maximum speed of the "down stream" control. And so on up to the six level not affecting the "down stream" controller whatsoever.
The purpose is to limit the maximum speed of my sewing. I am not expert at controlling speed. This allows me to control the maximum speed and gives more graduated increments of speed. Same as your dimmer switch regulating the speed of your Dremel.
#53
Super Member
Join Date: Aug 2013
Location: Springfield Oregon
Posts: 1,481
Here's another "dim bulb" piece of test gear from the days when I tinkered with old tube radios and hi-fi's.
It is a short circuit detector, that limits the current. It will also slow down a motor, it's not the same principle as a rheostat because almost full line voltage is still across the motor. This is actually a receptacle that came with a socket for one of the old screw in glass fuses. A bulb will light when the motors plugged into it. A motor has almost no resistance unless there is an open in the wiring somewhere. But the circuit breaker for that wall won't trip, even if there's a short, because the bulb limits current, a 1 amp motor, (around 100 watts give or take) with a 100 Watt bulb screwed in, will run about full speed. If you try to stop the motor, the bulb (which was kind of dim) will start to get brighter because the load is increasing.
Again, my caveat is don't get too wild with this stuff, don't do it on a wet basement floor, etc, etc etc...
[ATTACH=CONFIG]471704[/ATTACH] In the first photo, the test box is plugged in, but the motor isn't. Next photo, the motor is plugged in and running [ATTACH=CONFIG]471705[/ATTACH] I think that was a 75W bulb, motor was about 80% of full speed, next photo 100W bulb, brighter, and motor going almost full speed.
[ATTACH=CONFIG]471706[/ATTACH]Please excuse the bare ugly vise jaws on the motor, normally I'd cushion it with something. You may wonder why I did this...dunno just to see what would happen I guess.
It is a short circuit detector, that limits the current. It will also slow down a motor, it's not the same principle as a rheostat because almost full line voltage is still across the motor. This is actually a receptacle that came with a socket for one of the old screw in glass fuses. A bulb will light when the motors plugged into it. A motor has almost no resistance unless there is an open in the wiring somewhere. But the circuit breaker for that wall won't trip, even if there's a short, because the bulb limits current, a 1 amp motor, (around 100 watts give or take) with a 100 Watt bulb screwed in, will run about full speed. If you try to stop the motor, the bulb (which was kind of dim) will start to get brighter because the load is increasing.
Again, my caveat is don't get too wild with this stuff, don't do it on a wet basement floor, etc, etc etc...
[ATTACH=CONFIG]471704[/ATTACH] In the first photo, the test box is plugged in, but the motor isn't. Next photo, the motor is plugged in and running [ATTACH=CONFIG]471705[/ATTACH] I think that was a 75W bulb, motor was about 80% of full speed, next photo 100W bulb, brighter, and motor going almost full speed.
[ATTACH=CONFIG]471706[/ATTACH]Please excuse the bare ugly vise jaws on the motor, normally I'd cushion it with something. You may wonder why I did this...dunno just to see what would happen I guess.
#54
Banned
Join Date: Oct 2012
Location: San Lorenzo, CA
Posts: 5,361
how about the other end of the tech scale...
[ATTACH=CONFIG]471857[/ATTACH]
This is a slot cutter. This particular tool is going to be used to make the slot in the end of the spool pin shaft for a Willcox & Gibbs Automatic.
this is the slot
[ATTACH=CONFIG]471858[/ATTACH]
[ATTACH=CONFIG]471857[/ATTACH]
This is a slot cutter. This particular tool is going to be used to make the slot in the end of the spool pin shaft for a Willcox & Gibbs Automatic.
this is the slot
[ATTACH=CONFIG]471858[/ATTACH]
#55
Junior Member
Join Date: Oct 2013
Posts: 181
#60
Banned
Join Date: Oct 2012
Location: San Lorenzo, CA
Posts: 5,361
Thread
Thread Starter
Forum
Replies
Last Post
craftybear
Links and Resources
5
09-23-2010 11:57 AM