Bernina 830 just purchased. Need to know which threads to purchase for best results
#1
Senior Member
Thread Starter
Join Date: Jul 2010
Location: Rain Country USA
Posts: 300
Bernina 830 just purchased. Need to know which threads to purchase for best results
I have just purchased a Bernina 830 (the 8 series one). I'm curious as to the best threads to go with for this machine for each type of stitching --- regular garment sewing; embroidery; and finally machine quilting. Also --- having purchased my used car as it were, I now need to get a sturdy desk/table to put it on for using --these heavier machines will need a sturdier support system than a tv tray.
#3
Super Member
Join Date: Jul 2013
Location: Houston, TX
Posts: 9,550
I've had 2 Bernina's and the only threads I've had problems with were metallics. They tended to break so I just have to drop my top tension down very low. Then everything was good. I have a 930 that I haven't really used a lot and it seems to use any thread without problems.
#4
Member
Join Date: Jun 2011
Location: Murrieta, CA
Posts: 64
Congrats on the used car equivalent, I'm sure you'll have more fun and less trouble with the 830! As for thread, I agree with Tartan that strength, wt and LINT are my main criteria.
If you or someone you know, is good with power hand tools (mainly a jig saw and drill), I used a 4' x 4' piece of 1/2" white melamine (cut down from a 4x8 sheet), added flanges and used 1" pvc piping for legs (with caster wheels) and cross members. I then cut out the profile of my machine a few inches from the right corner and lowered that cutout down about 3 inches to make the level of my presser plate a little lower than the level of the table (with some cardboard for fine-tuning). I then used some brackets to secure the lowered cut out to the bottom side of the 4x4 table.
This set up has lasted a LONG time, has given me enough room to FMQ King sized quilts and under normal conditions, gives me room to use my big rotary cutter mat at the other end of the table. It was cheap but did take some work.
If you or someone you know, is good with power hand tools (mainly a jig saw and drill), I used a 4' x 4' piece of 1/2" white melamine (cut down from a 4x8 sheet), added flanges and used 1" pvc piping for legs (with caster wheels) and cross members. I then cut out the profile of my machine a few inches from the right corner and lowered that cutout down about 3 inches to make the level of my presser plate a little lower than the level of the table (with some cardboard for fine-tuning). I then used some brackets to secure the lowered cut out to the bottom side of the 4x4 table.
This set up has lasted a LONG time, has given me enough room to FMQ King sized quilts and under normal conditions, gives me room to use my big rotary cutter mat at the other end of the table. It was cheap but did take some work.
#5
Power Poster
Join Date: Jan 2011
Location: Southern USA
Posts: 16,010
Every machine dealer in my area uses poly thread for demoing in the new machines. All models. The settings are set for poly from the company. I think any good thread will be fine, the main thing is to have the right size needle for the wt and ply of the thread. This goes for all types of stitching. The needle and thread have to be compatible. The 830 is a big and heavy machine. I would certainly invest in a quality sewing table for it.
#7
Super Member
Join Date: Feb 2014
Location: Wis
Posts: 5,928
I have an 820, which is like yours except I don't have embroidery. My machine doesn't like invisible thread or metallic or Dual Duty. It's probably me not being able to figure out the adjustments though. I use mostly any Superior thread on the cones - no specific ones. Mostly I like polyester for piecing. My machine seems to like the Superior ones the best. I use Aurifill too. Have fun with your new machine!
#8
Senior Member
Thread Starter
Join Date: Jul 2010
Location: Rain Country USA
Posts: 300
Thanks everyone! I am eager to get my sewing space set up for my new arrival --- hopefully before Christmas --- my dealer is letting me keep my machine there until I have the basics in my experience which gives me time to figure out the desk/table. I have a vintage desk with a one inch thick old growth fir top that I hope will accommodate "Baby" with a few reinforcements.
#9
Senior Member
Join Date: Jun 2011
Location: Cedar Falls, IA
Posts: 918
Your machine should be able to take about any quality thread. I love SoFine from Superior for piecing. I generally use Guterman for general sewing. For quilting I use whatever has the color and weight I like, but mostly from Superior because I can get it easily here. Stay away from Coats and Clark in general. Metallics take a comfort with adjusting tension that you might need more experience. I have used Yenmet very successfully though.
#10
I had a rag rug business and had many employees and machines. I ended up with Bernina 1020 being the go to best machine, sewed in all situations. Even sewed when it was sick. Thread I used was Gutterman which did not untwist in damp weather.
Thread
Thread Starter
Forum
Replies
Last Post
suspendedglass
Main
20
05-02-2019 06:43 PM