1/4 seam
10-04-2012, 07:45 AM
#11
Super Member
Join Date: Mar 2012
Location: Texas, USA
Posts: 5,896
Since your needle can't be moved in tiny increments, try using a different foot. If you have a foot with a groove in it, like for satin stitch, give that a try. I accidentally found out one particular presser foot will give me a scant 1/4", by moving my 1/4" into its groove, just a bit past a true 1/4".
On my old machine, I would sometimes measure each presser foot, until I found one of the proper width, for whatever seam I wanted, then used the edge of that foot, as a guide.
On my old machine, I would sometimes measure each presser foot, until I found one of the proper width, for whatever seam I wanted, then used the edge of that foot, as a guide.
10-04-2012, 08:33 AM
#12
Senior Member
Thread Starter
Join Date: Jul 2012
Location: Long Island
Posts: 798
Since your needle can't be moved in tiny increments, try using a different foot. If you have a foot with a groove in it, like for satin stitch, give that a try. I accidentally found out one particular presser foot will give me a scant 1/4", by moving my 1/4" into its groove, just a bit past a true 1/4".
On my old machine, I would sometimes measure each presser foot, until I found one of the proper width, for whatever seam I wanted, then used the edge of that foot, as a guide.
On my old machine, I would sometimes measure each presser foot, until I found one of the proper width, for whatever seam I wanted, then used the edge of that foot, as a guide.
10-04-2012, 10:52 PM
#13
Super Member
Join Date: Apr 2007
Location: Phoenix, AZ
Posts: 2,943
Warning if your machine reverts to the center position when turned off:
Whenever I am doing a project that involves moving the needle position I put a note on my machine with the project name and the needle used. I use painter's tape to hold the little post it note ... so it won't fall off and is more visible.
ali
Whenever I am doing a project that involves moving the needle position I put a note on my machine with the project name and the needle used. I use painter's tape to hold the little post it note ... so it won't fall off and is more visible.
ali
10-06-2012, 05:20 AM
#14
Senior Member
Join Date: Nov 2006
Location: Pinellas Park, FL
Posts: 607
Warning if your machine reverts to the center position when turned off:
Whenever I am doing a project that involves moving the needle position I put a note on my machine with the project name and the needle used. I use painter's tape to hold the little post it note ... so it won't fall off and is more visible.
ali
Whenever I am doing a project that involves moving the needle position I put a note on my machine with the project name and the needle used. I use painter's tape to hold the little post it note ... so it won't fall off and is more visible.
ali
10-06-2012, 07:38 AM
#16
Senior Member
Join Date: May 2012
Location: Las Vegas, NV - transplanted from Southeastern PA
Posts: 324
I think the best advice I can give is be consistant. The quilt may end up being a little smaller than the pattern if you don't get a scant 1/4 but if all the seams are the same I don't think it will matter. I think Bargello calls for narrower seams because on some of the very narrow pieces, you don't want the seam allowances to overlap. I have a good 1/4 foot and I move my needle position over one space when A pattern calls for a scant 1/4.
10-06-2012, 01:05 PM
#17
Super Member
Join Date: Dec 2010
Location: Wisconsin
Posts: 2,122
Where you might run into a problem not perfecting your scant quarter inch is when piecing and not having the same number of seams on each section of the block. Or having 1 piece with no seams and trying to connect it with a piece with a few seams. It really can make a difference. Anyway, that's where I have problems.
10-06-2012, 05:03 PM
#19
Member
Join Date: Mar 2012
Location: Southeastern NC
Posts: 25
The other thing I've done is to take a tape measure, lay it out to 1/4 inch and mark the machine with a sharpie. If I want a scant inch I sew on the left edge of the mark and if I want a regular 1/4 inch I sew on the right edge of the mark. Has worked pretty well for me and it gives me a nice mark to guide the whole piece into the feeder dogs.
10-06-2012, 05:22 PM
#20
Super Member
Join Date: Aug 2010
Location: Mena, Arkansas
Posts: 1,351
Thread
Thread Starter
Forum
Replies
Last Post
craftybear
Links and Resources
5
10-01-2011 07:09 PM
craftybear
Links and Resources
6
10-01-2011 07:03 PM
craftybear
Links and Resources
4
10-01-2011 07:02 PM
craftybear
Links and Resources
2
06-14-2010 10:02 PM
