Borders On Quilts
#1
Ok.. you can only read this if you promise not to yell at me... :oops:
So... the quilts that I have made with borders.. I am guessing I have done them all wrong. I measure the width I want, and cut the length longer than what I need.. sew it on and trim it even. I normally put the sides on first, than the top and bottom. I am beginning to think (from reading the Board.. keep in mind, I am totally self taught) that this is BAD :thumbdown:
So... is the way I am doing it really THAT bad? Will it make it difficult to be quilted on a LA? I have read about the measuring down or across the center.. and then pinning at both ends and easing the fabric for a good fit? Is this a "do this or it will be REALLY wrong" thing?
Thanks for the comments in advance. :)
So... the quilts that I have made with borders.. I am guessing I have done them all wrong. I measure the width I want, and cut the length longer than what I need.. sew it on and trim it even. I normally put the sides on first, than the top and bottom. I am beginning to think (from reading the Board.. keep in mind, I am totally self taught) that this is BAD :thumbdown:
So... is the way I am doing it really THAT bad? Will it make it difficult to be quilted on a LA? I have read about the measuring down or across the center.. and then pinning at both ends and easing the fabric for a good fit? Is this a "do this or it will be REALLY wrong" thing?
Thanks for the comments in advance. :)
#3
Okaaaay...good news is that what you have been doing is not 'terrible'. The reason that a person should measure the width or length thru the center of the quilt top, is that sometimes the edges can stretch, that's all. And if those edges have stretched, then the borders will actually be longer than the center of the quilt. When it has been quilted, bound and put on a bed, it could look like a skirt that has been 'sat out'.
So, long story short, measuring thru the center of the quilt top helps to keep the width and length even along the whole sides.
So, long story short, measuring thru the center of the quilt top helps to keep the width and length even along the whole sides.
#5
Super Member
Join Date: Nov 2010
Location: Snowy Minnesota
Posts: 1,378
If it makes you feel any better, that's how I attached the borders of the first quilt I made. Everything turned out fine, tho some "beginner's luck" may have been involved.
Shortly after finishing that quilt, I learned about the "measure through the middle" technique. I think GingerK is exactly right as to why this is a better method. Count your lucky stars, but live and learn. :-)
Shortly after finishing that quilt, I learned about the "measure through the middle" technique. I think GingerK is exactly right as to why this is a better method. Count your lucky stars, but live and learn. :-)
#7
Power Poster
Join Date: Dec 2010
Location: Michigan
Posts: 11,276
You have probably been lucky! The problem is that you can stretch the quilt, and make the border bigger than it should be. This results in wavy borders that can't be 'quilted out'. It's more of a problem with larger quilts, so if you are doing smaller ones, it's less of an issue. the border should be pinned the entire length before you sew it.
As far as 4 Dog's question, I would measure the quilt, then transfer that measurement to the piece you cut for the border, leaving extra fabric at the start & end. You can then pin the correct length of border to the quilt, and still have extra for the miters.
As far as 4 Dog's question, I would measure the quilt, then transfer that measurement to the piece you cut for the border, leaving extra fabric at the start & end. You can then pin the correct length of border to the quilt, and still have extra for the miters.
#8
You can definitely still do the miter - you're still measuring thru the centres, pinning to fit and also having the extra at each end to do the miters.
So if your quilt is 60" square and your borders 4", you're going to cut about 70".
On the quilt, fold it in half and mark the half way point.
Mark the centre point of the cut border (chalk, notch, pin), and measure out half of the quilt width/length (30") and mark that (chalk, notch, pin). Pin the border to the quilt, easing in if necessary.
To get even more precision, mark the border and the quilt in eighths - fold in half, mark the half-way point; fold in half again, mark that point; fold in half again and mark again. Match up each mark on the quilt and border, easing where necessary.
Be sure to have a bit more width than the width of the border, on each corner, for the miters. And remember to start and stop at the 1/4 inch measure away from the edge so you can get a nice miter.
So if your quilt is 60" square and your borders 4", you're going to cut about 70".
On the quilt, fold it in half and mark the half way point.
Mark the centre point of the cut border (chalk, notch, pin), and measure out half of the quilt width/length (30") and mark that (chalk, notch, pin). Pin the border to the quilt, easing in if necessary.
To get even more precision, mark the border and the quilt in eighths - fold in half, mark the half-way point; fold in half again, mark that point; fold in half again and mark again. Match up each mark on the quilt and border, easing where necessary.
Be sure to have a bit more width than the width of the border, on each corner, for the miters. And remember to start and stop at the 1/4 inch measure away from the edge so you can get a nice miter.
#9
There is no bad way as long as it works for you. I have never done all these "required" measurements and I think my quilts lay nice and flat. I do the sides first and then the top and bottom and I only measure the edge I am doing.
I figure it is just like making a block a little bigger than needed and trimming it to square after it is finished.
I cut the border about 6" longer than my measurement of one side and leave a 3" tail on each end. After it is sewn I trim the extra off each end to square it up and then repeat for the other side, then top and bottom.
If you need that extra assurance of a correct measurement then take as many as you want to be extra sure.
If there is a reason not to do it this way I would like to know 'cause I can't figure why not. I know this is not the most accurate way but it works for me. If there is a better way I would like to know.
Now I'm totally confused! What measurement should you be aiming for? the center or the edge?
Milliequilter didn't say anything about wanting to miter the corners so what is all the reference to miters?
I'm really confused? Old dog new trick thing!
I figure it is just like making a block a little bigger than needed and trimming it to square after it is finished.
I cut the border about 6" longer than my measurement of one side and leave a 3" tail on each end. After it is sewn I trim the extra off each end to square it up and then repeat for the other side, then top and bottom.
If you need that extra assurance of a correct measurement then take as many as you want to be extra sure.
If there is a reason not to do it this way I would like to know 'cause I can't figure why not. I know this is not the most accurate way but it works for me. If there is a better way I would like to know.
Now I'm totally confused! What measurement should you be aiming for? the center or the edge?
Milliequilter didn't say anything about wanting to miter the corners so what is all the reference to miters?
I'm really confused? Old dog new trick thing!
Thread
Thread Starter
Forum
Replies
Last Post