Can't loosen the screws
#1
Can't loosen the screws
I finally found time to take my 201 apart and do a clean up on her but of course I have two stubborn screws that won't budge. Can someone tell me how I can get them to turn?
KAT
KAT
#2
I am not an expert, and it depends where the screws are located. But I place a small drop of oil on the screw and let it sit. It usually helps it to turn.
#4
Super Member
Join Date: Oct 2010
Location: northern California
Posts: 1,098
Use a bit of oil and then, while waiting for that to do it's thing, go to Harbor Freight and get their mini screw driver that has gears and several types of screw driver designs. It will work in any area down to an inch of space. I have bad arthritis in my hands and DH got this for me and, because of its design of gears I can use it! It cost less than $5. He used to take off my bobbin cover so I could put a drop of oil in, now I easily do it myself!
#5
Banned
Join Date: Oct 2012
Location: San Lorenzo, CA
Posts: 5,361
I use a screwdriver that is as wide as the slot and I make sure it goes ALL the way to to the bottom of the slot
A little tapping might help. With the screw driver in the slot GENTLY tap the handle end with a hammer.
(This idea of this is to vibrate loose the rust/grime)
Liquid Wrench (easy to find) or Kroil (better but harder to find.)
PB blaster works(from autoparts stores), but I've been told to be careful not to get it on the rest of the machine
A little heat from a hair dryer also helps.
A little tapping might help. With the screw driver in the slot GENTLY tap the handle end with a hammer.
(This idea of this is to vibrate loose the rust/grime)
Liquid Wrench (easy to find) or Kroil (better but harder to find.)
PB blaster works(from autoparts stores), but I've been told to be careful not to get it on the rest of the machine
A little heat from a hair dryer also helps.
#6
Super Member
Join Date: Feb 2012
Posts: 8,091
I'll bet the two screws are the needle plate screws.
If so start with the oil, penetrating oil if you have it.
Then go to harbor freight and get a small ratchet handle bit driver set. You cannot get a straight shot at those screws with a normal screwdriver. Use the proper size bit held straight and carefully apply the pressure to the screws.
I've had to do many of them that way. Strangely a lot of people crank those tiny screws down way too tight. I guess they think they are holding the whole machine together.
Joe
If so start with the oil, penetrating oil if you have it.
Then go to harbor freight and get a small ratchet handle bit driver set. You cannot get a straight shot at those screws with a normal screwdriver. Use the proper size bit held straight and carefully apply the pressure to the screws.
I've had to do many of them that way. Strangely a lot of people crank those tiny screws down way too tight. I guess they think they are holding the whole machine together.
Joe
#8
Super Member
Join Date: Feb 2012
Posts: 8,091
AZKAT,
You don't need to take the wheel off to get to the grease tube caps. But to remove the hand wheel, just remove the stop motion knob and pull it off. Just like a normal machine.
The ratchet bit driver will work on the grease tube caps too, or a pair of pliers with the jaws padded with rubber tubing.
Joe
You don't need to take the wheel off to get to the grease tube caps. But to remove the hand wheel, just remove the stop motion knob and pull it off. Just like a normal machine.
The ratchet bit driver will work on the grease tube caps too, or a pair of pliers with the jaws padded with rubber tubing.
Joe
Thread
Thread Starter
Forum
Replies
Last Post
Ms Grace
For Vintage & Antique Machine Enthusiasts
7
09-28-2016 01:49 PM
sunnyhope
Main
13
09-18-2009 04:32 PM