Go Back  Quiltingboard Forums >
  • Main
  • For Vintage & Antique Machine Enthusiasts
  • Is it possible to 'spot' shellac? >
  • Is it possible to 'spot' shellac?

  • Is it possible to 'spot' shellac?

    Thread Tools
     
    Old 11-18-2014, 08:25 AM
      #1  
    Junior Member
    Thread Starter
     
    Champanier's Avatar
     
    Join Date: Jan 2014
    Location: Samsonville, New York
    Posts: 268
    Default Is it possible to 'spot' shellac?

    I have a 42 cabinet that's in nice shape over all, although the veneer is lifted on the bottom in one place. I read to use an old credit card to push in glue, then clamp, so I think that's okay.

    The bigger problem, I think, is a ring on the top where the finish is completely gone. I wondered whether Glenn's technique with denatured alcohol and shellac would work on just that spot? Could I kind of feather in from the areas that are okay? Or is there another way to restore the shine to that spot without redoing the whole top?

    Thank you![ATTACH=CONFIG]499321[/ATTACH]
    Attached Thumbnails image.jpg  
    Champanier is offline  
    Old 11-18-2014, 08:37 AM
      #2  
    Super Member
     
    jmabby's Avatar
     
    Join Date: Dec 2010
    Location: Minnesota, Land of 10,000 Lakes
    Posts: 1,490
    Default

    I have a similar problem, where there is a spot worn off from laying on the bar that comes out when you open the lid of the cabinet. Thanks
    jmabby is offline  
    Old 11-18-2014, 10:21 AM
      #3  
    Super Member
     
    Join Date: Mar 2010
    Location: Huntsville, AL
    Posts: 2,609
    Default

    Yes you can spot shellac. First start out with a little shellac with a drop or two of linseed oil and french polish the area. Keep doing this many times until the area is level with the rest then French polish to blend in. You may want to use the amber shellac first to darken the water ring then use clear to finish the repair. You can also use a fine artist brush and brush the shellac on in thin coats until it is level with the rest of the finish. Waiting about an hour between coats, should only take about three thin coats. Then You can french polish the area smooth. After a week of curing wax the entire cabinet with a good quality past wax. I use Bri wax.
    Skip
    Glenn is offline  
    Old 11-18-2014, 11:47 AM
      #4  
    Junior Member
    Thread Starter
     
    Champanier's Avatar
     
    Join Date: Jan 2014
    Location: Samsonville, New York
    Posts: 268
    Default

    Originally Posted by Glenn
    Yes you can spot shellac.
    That's great news! Thanks so much for the clear instructions. Do you think it would help to lightly sand the dark edges around the ring?
    Champanier is offline  
    Old 11-18-2014, 12:15 PM
      #5  
    Super Member
     
    Join Date: Mar 2010
    Location: Huntsville, AL
    Posts: 2,609
    Default

    You can but not required the new shellac will melt into the old. If you do sand keep it on the edges only are you will end up with a larger area to repair.
    Skip
    Glenn is offline  
    Old 11-18-2014, 01:43 PM
      #6  
    Super Member
     
    manicmike's Avatar
     
    Join Date: Mar 2013
    Location: Brisbane, Australia
    Posts: 1,850
    Default

    Originally Posted by Glenn
    You can but not required the new shellac will melt into the old. If you do sand keep it on the edges only are you will end up with a larger area to repair.
    Skip
    Glenn, you're brilliant. How many cabinets don't have this type of damage?
    manicmike is offline  
    Old 11-19-2014, 06:18 AM
      #7  
    Junior Member
     
    Join Date: Nov 2010
    Location: Harrisonburg, VA
    Posts: 167
    Default

    Originally Posted by Glenn
    You can but not required the new shellac will melt into the old. If you do sand keep it on the edges only are you will end up with a larger area to repair.
    Skip
    Could we see some pics of ones you have restored? Please!!
    TGood is offline  
    Old 11-19-2014, 10:36 AM
      #8  
    Super Member
     
    Join Date: Mar 2010
    Location: Huntsville, AL
    Posts: 2,609
    Default Bruce cabinet and machine I cleaned up

    The cabinet was cleaned and then french polished then waxed with Bri wax and very fine steel wool. the bad areas were spot shellaced then went over the entire cabinet with french polish and waxed. The machine was so dirty I could not see the decals so cleaned and french polished it also. This one was done about two years ago. Sews great. I have about 6 more that I have done this way.
    Skip
    Attached Thumbnails christmas-2012-084.jpg   christmas-2012-085.jpg   christmas-2012-062.jpg   christmas-2012-067.jpg  

    Last edited by Glenn; 11-19-2014 at 10:38 AM. Reason: Add info
    Glenn is offline  
    Old 11-19-2014, 11:03 AM
      #9  
    Junior Member
    Thread Starter
     
    Champanier's Avatar
     
    Join Date: Jan 2014
    Location: Samsonville, New York
    Posts: 268
    Default

    Wow, Glenn, that is breathtaking!

    Do you have a preference between applying the shellac to the spot with an artist brush and then french polishing or doing only french polishing? I'd like to just try the artist brush approach first, because I think it will be easier to tell what I'm doing.

    Do you use canned shellac or dissolve flakes? (The flakes I've found are really expensive.)
    Champanier is offline  
    Old 11-19-2014, 11:46 AM
      #10  
    Super Member
     
    Join Date: Mar 2010
    Location: Huntsville, AL
    Posts: 2,609
    Default

    Linda, I use both the flakes and canned shellac. It is perfectly fine to use the shellac in qt cans you get at Lowes or Home Depot. It is about $13 a can here but will last you thru several cabinets. Flakes can get pricey but they are better than the canned because you can mix up what you need. I have had excellent results with the canned so go for that. When I had my restoration shop I would use only the flakes but now retired I use the canned it is easier.
    Skip
    Glenn is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    Glenn
    For Vintage & Antique Machine Enthusiasts
    718
    07-07-2024 05:15 AM
    Glenn
    For Vintage & Antique Machine Enthusiasts
    105
    06-17-2023 07:05 AM
    Glenn
    For Vintage & Antique Machine Enthusiasts
    35
    07-03-2014 08:44 PM
    Cecilia S.
    For Vintage & Antique Machine Enthusiasts
    2
    01-03-2014 12:39 PM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is Off
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter