blocks not same size
#51
Also, sometimes if you end up with triangles on the outside edge of a block, it can stretch, that is why careful dry pressing is a must.
I think the best advice is to have fun- remember no one is going to notice if the quilt is off a little if they are passing by on a galloping horse!
:D :D :D
I think the best advice is to have fun- remember no one is going to notice if the quilt is off a little if they are passing by on a galloping horse!
:D :D :D
#53
Have you tried to put a frame around your blocks and then square them all up to the same size? I would use a soild color and use the largest block as a guide and put a frame around each block that can be the same size as the largest block. I plan to do this to a paper-pieced quilt that I am working on where the blocks are different sizes.
#54
Power Poster
Join Date: May 2008
Location: MN
Posts: 24,659
Originally Posted by Donna in Mo
Be sure and use a dry iron. If you steam press, they will shrink. I know this from experience. My motto is I think I can, I think I can, I think I can, and just keep trying. You will get it.
I soak my fabrics in hot water - wash in cool to warm - dry on permanent press.
I have no noticeable shrinking when I press my blocks - either dry or with steam.
#55
Hope I can explain clearly what I do by adding the sashing strips to square the block. If your block is to be 12 1/2" square, lay the block in the left hand corner of your cutting mat. If the block is too small lay it in the corner with equal distance all around to come up with the 12 1/2" square. Lay the sashing strips to the two opposing sides . making sure they are 12 1/2", pin and sew. Do the same to the other opposing sides. If you can't get enough of a seam allowance sew what you can and make it up on the next block that has had the sashing added. If the block is too big move the sashing strips in a bit and try easing in some of the excess of the block. I'm a very visual person, so if this doesn't make sense let me know and I'll walk you through the process.
#56
Super Member
Join Date: Feb 2010
Location: Wisconsin
Posts: 1,152
Hello 4 cities, IL. I recently bought a Kenmore machine. It has a quarter inch, a scant quarter inch and a three-quarter inch setting. Love it, as I make items that need a smaller seam.
Originally Posted by PMY in QCA-IL
Practice sewing "scant" 1/4" seams until you can get a consistent measurement. Find a spot on your sewing machine or mark with tape where you can end up with a "scant" 1/4" seam. ("Scant" means a thread ot two just short of a measured 1/4".)
#57
Super Member
Join Date: Feb 2010
Location: Wisconsin
Posts: 1,152
Yes, Jennie Girl there is such a thing as a scant 1/4 inch. I've used in for years by appoximating with my eye, now, I don't need to figure it out anymore.
I recently purchased a Kenmore Machine that has many settings. One is the width of seams. There is a scant 1/4 inch, a 1/4 inch and a 3/4 inch seam width. I just turn a button and have the stitch I want.
I recently purchased a Kenmore Machine that has many settings. One is the width of seams. There is a scant 1/4 inch, a 1/4 inch and a 3/4 inch seam width. I just turn a button and have the stitch I want.
#58
Super Member
Join Date: Feb 2010
Location: Wisconsin
Posts: 1,152
I have a suggestion. Just be accurate first in purchasing material. # 1. Don't use stretchy fabric unless you use it all over the quilt.# 2. When cutting your pattern, make sure your cuts are accurate. (try the block first as the templates request, some templates are slightly off). If they are off, even an enth of an inch, it throws the whole block off. # 3. Make sure all your seams are accuratly measured. Any diviation of this width will cause a problem.
# 4. Slow down! It took God 6 days to creat the world and on the fifth day, He rested.
# 4. Slow down! It took God 6 days to creat the world and on the fifth day, He rested.
Thread
Thread Starter
Forum
Replies
Last Post
AngelinaMaria
Main
7
02-13-2013 07:49 AM
oksewglad
Pictures
17
09-25-2011 08:17 PM