Flying Geese Problems
#11
Banned
Join Date: Nov 2010
Posts: 4,134
This is a ridiculous question and please don't be insulted, but I'm just wondering something.
When you're placing the squares on the rectangle, are you lining them up as indicated in the diagram in the pattern?
Or are you stacking the square directly on the rectangle so that 3 sides of the square (top, outer edge and bottom) line up exactly with those of the rectangle?
And once you get it figured out, MadQuilter's #5-6 are really good tips. The all were, but those are especially helpful.
When you're placing the squares on the rectangle, are you lining them up as indicated in the diagram in the pattern?
Or are you stacking the square directly on the rectangle so that 3 sides of the square (top, outer edge and bottom) line up exactly with those of the rectangle?
And once you get it figured out, MadQuilter's #5-6 are really good tips. The all were, but those are especially helpful.
#12
Originally Posted by stitchinwitch
Try this method
http://www.youtube.com/watch?v=78Mu0C_QL8Y
http://www.youtube.com/watch?v=78Mu0C_QL8Y
#13
Super Member
Join Date: Jan 2011
Posts: 1,812
Here's how I do it. Works every time. Everything you need to know is on this one page. I also use Eleanor's rulers to make sure the finished piece is exactly the measurement I need it.
http://www.patchpieces.com/files/flyinggeese.pdf
http://www.patchpieces.com/files/flyinggeese.pdf
#15
Super Member
Join Date: Aug 2010
Location: Piedmont Virginia in the Foothills of the Blue Ridge Mtns.
Posts: 8,562
Originally Posted by thelondonzoo
....I'm using a 2 1/2" x 4 1/2" rectangle and then I'm trying to sew on two 2 1/2" squares.
I suggest sewing the block sections together with the geese section on top (undeerf the needle) so that you can see exactly where you need to put your seam allowance to keep your points.
AND, because you are only cutting out the triangle of the small sq., you will have a slightly thicker seam when you open to press.....soooooo, let the needle fit within the seam allowance by a couple of stitches so there's extra room to open and press.
Jan in VA
Dotted line is your sewing line inside the seam allowance
[ATTACH=CONFIG]240892[/ATTACH]
#16
#17
Hope you get it worked out. I got this tute on the board and though it was a great technique for sewing rows.
"A Quilter's Choice" Amazing NEW Technique for Flying Geese"
http://www.youtube.com/watch?v=Ue1mBo9968Y
"A Quilter's Choice" Amazing NEW Technique for Flying Geese"
http://www.youtube.com/watch?v=Ue1mBo9968Y
#19
I don't know if I'll be able to explain how I do mine but hopefully I can. It always seems like there is a little difference in the size of the pieces you measure check and cut but sometimes they just come out different. So, I will lay the squares further to the bottom because they are going to be flipped and pressed up. I press very carefully as to not stretch or wrap the fabric because it's on the bias. Then when I trim my block I make sure that there is a 1/4 inch to the point.
You could also try cutting your squares a smidge bigger and then trim away the excess.
You could also try cutting your squares a smidge bigger and then trim away the excess.
#20
Such great advice on here. I think practice helps. Use extra fabric & try several different ways....as posted on this board,until you find the way that works best for you.Don't be in a rush, just practice.
Thread
Thread Starter
Forum
Replies
Last Post
craftybear
Links and Resources
6
04-19-2011 05:27 PM