Go Back  Quiltingboard Forums >
  • Main
  • Long border strips up or down? >
  • Long border strips up or down?

  • Long border strips up or down?

    Thread Tools
     
    Old 12-01-2019, 02:57 PM
      #1  
    Member
    Thread Starter
     
    Join Date: Mar 2011
    Location: KCMO area
    Posts: 57
    Default Long border strips up or down?

    Should I be sewing long border strips on rows (or to edge of quilt top) with those strips facing up toward the needle or down toward the feed dogs? Edges of pieced blocks where seams meet are giving me headaches trying to keep them from folding the wrong way and getting stitched into bulky lumps. Should I be using a walking foot? What if I don’t have a walking foot? Any advice from veteran sewists?
    Kcmomto2 is offline  
    Old 12-01-2019, 03:09 PM
      #2  
    Super Member
     
    Join Date: Aug 2018
    Location: Greater Peoria, IL -- just moved!
    Posts: 6,164
    Default

    Well, I'm a pinner and I press open. If I have the choice between what to put under the needle, it is the side with the most seams and every leading seam is pinned. I pin low, they are never near my needle. I much prefer to have the unseamed side on the bottom even though the usual rule is the bigger piece on the bottom, smaller on the top.

    Again, I pin and have no nesting to guide me.
    Iceblossom is offline  
    Old 12-01-2019, 03:14 PM
      #3  
    Member
     
    jessicalebo's Avatar
     
    Join Date: Aug 2019
    Location: South Carolina
    Posts: 34
    Default

    Sew them which ever way is easiest for you. If there are a lot of seams I like to put the seams up so I can control which direction the end up. But normally I find it easier to have the smaller border piece on top. Basically it's easier to have both sides facing up... so helpful right?! Do which ever require less frustration and seam ripping. There is no right or wrong.

    I never use my walking foot personally. I find it annoying to change feet, so I don't bother. That said, walking feet attachments aren't super expensive and many people them, so it may be a good option for you. I'm sure others will weigh in on that one.

    Last edited by QuiltnNan; 12-01-2019 at 05:21 PM. Reason: shouting/all caps
    jessicalebo is offline  
    Old 12-01-2019, 03:21 PM
      #4  
    Super Member
     
    Join Date: May 2017
    Location: Sunny Florida
    Posts: 4,431
    Default

    I stay stitch the quilt edge and the border edge first. Mark each one into quarters and pin, pin, pin. Sometimes I use the walking foot w/ the 1/4 inch foot.

    You can use a dot of elmer's school glue or glue stick to hold those pesky seams in place.
    Rhonda K is offline  
    Old 12-01-2019, 03:39 PM
      #5  
    Super Member
     
    EasyPeezy's Avatar
     
    Join Date: Mar 2010
    Location: Canada
    Posts: 3,460
    Default

    If I have a choice I put the smooth side down then I can see the piecing.
    But if I don't have a choice then I use a thin line of Elmer's washable glue
    and set the seam with the iron before sewing. I use a stiletto to push the
    seam as I go if needed. Since I starch my fabric it usually behaves but I
    still check to make sure it's going under the needle the right way.
    You can put a pin ahead of each seam to remind you to stop, remove pin
    and check. Sounds like a pain but you won't have any folded seam that
    way.
    EasyPeezy is offline  
    Old 12-01-2019, 04:26 PM
      #6  
    Power Poster
     
    Jingle's Avatar
     
    Join Date: Dec 2009
    Location: Outside St. Louis
    Posts: 38,224
    Default

    I sew borders on the top, seams toward machine. I look to make sure seams stay where they should.
    Jingle is offline  
    Old 12-01-2019, 07:09 PM
      #7  
    Super Member
     
    Join Date: Sep 2019
    Location: North Idaho
    Posts: 1,695
    Default

    I prefer to sew with the border strip on top. I usually hold both layers at a slight angle above the machine surface. The seams are less likely to catch and turn under that way, plus I feel like i have more control and it seems to help both layers feed more consistently.
    LAF2019 is offline  
    Old 12-01-2019, 07:24 PM
      #8  
    Power Poster
     
    SusieQOH's Avatar
     
    Join Date: Jul 2017
    Location: Central Ohio
    Posts: 15,236
    Default

    The only way I've ever done it is to have the strips facing the needle.
    SusieQOH is offline  
    Old 12-01-2019, 08:42 PM
      #9  
    Power Poster
     
    Join Date: Mar 2011
    Location: Ontario, Canada
    Posts: 41,535
    Default

    I sew the pieces with the most seams on top where I can watch that the seam allowances go the correct way.....however that is after the pieced part is well pinned to the border. If you just sew your pieced top to a long border strip, it will stretch and you will not fit your border. You can also ease the pieced top towards the needle as you sew with a straight pin to coax it to feed well.
    Tartan is offline  
    Old 12-01-2019, 08:51 PM
      #10  
    Power Poster
     
    Join Date: May 2008
    Location: MN
    Posts: 24,644
    Default

    I mark borders to match the blocks before I pin them.

    I think I usually put the side with the most pieces facing the feed dogs -
    bearisgray is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    AFQSinc
    Main
    15
    06-19-2012 12:35 PM
    craftybear
    Links and Resources
    1
    08-10-2011 12:37 PM
    wildyard
    Main
    104
    02-10-2011 09:32 AM
    quiltykim
    Main
    17
    09-05-2010 06:06 AM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is On
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter